Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TKR Group 83 30 5 A72 B58
Summary of Contents for TKR Group 83 30 5 A72 B58
- Page 1 83 30 5 A72 B58 Adapter Translation of the original owner’s manual WARNING This Assembly manual is a supplement to the original owner‘s manual Seat support frame 83 30 2 473 334 and must only be used together with the Owner‘s manual.
-
Page 3: Table Of Contents
Safety General instructions Explanation of symbols Designations Scope of supply Safety instructions Technical data Technical data Intended use Working with the adapter - basic principles Assembly Assembly Completing an operation and storing the adapter Maintenance Troubleshooting Regular checking and maintenance Service Disposal Warranty &... -
Page 4: General Instructions
1.1 General instructions State-of-the-art Declaration of Conformity This tool is state-of-the-art technology. To ensure that the The tool has been manufactured and inspected in equipment operates safely, it must be operated in a proper and compliance with European directives. The Decla- safety-conscious manner. -
Page 5: Explanation Of Symbols
1.2 Explanation of symbols This owner‘s manual contains some sections with internationally recognized warning symbols, hazard warnings and general mandatory signs. The individual symbols are explained below. Follow all the instructions and safety rules. Follow the manual Please note the following... Turn anti-clockwise Wear protective gloves Arrow to clarify compression... -
Page 6: Designations
1.3 Designations Adapter 83 30 5 A72 B58 52 Serial No.: XXXXX, CW: XX/XX Max. Load / WLL: 52kg Weight: 0,7kg TKR Spezialwerkzeuge GmbH Am Waldesrand 9-11, D-58285 Gevelsberg For use only with 83 30 0 495 187 and 83 30 2 473 334 Designation on the adaptor plate of the cross member Manufacturer’s label... -
Page 7: Scope Of Supply
1.4 Scope of supply Adapter Change carriage left 2x 83 30 5 A72 B58 Cheese head screws with knurl M10x50 2x... -
Page 8: Safety Instructions
1.5 Safety instructions The tool is strictly approved solely for the purpos- CAUTION es for which the manufacturer has designed it. Risk of material damage and bodily injury The tool must only be used for the activities described in this Untrained or uninstructed personnel are prohibited from operat- owner's manual. -
Page 9: Technical Data
(for deformation), three times (for fracture) Temperature -10°C to +60°C 2.1.1 front 2.1.2 left Adapter 83 30 5 A72 B58 52 Serial No.: XXXXX, CW: XX/XX Max. Load / WLL: 52kg Weight: 0,7kg TKR Spezialwerkzeuge GmbH Am Waldesrand 9-11, D-58285 Gevelsberg... -
Page 10: Intended Use
2.2 Intended use Intended The adapter must only be used for the support frame of a BMW approved seat in ac- cordance with the specifications of BMW AG. Only use the adapter in connection with the seat support frame 83 30 2 473 334, and the assembly stand 83 30 0 495 187. It is essential that you follow the instructions of all three tools. -
Page 11: Working With The Adapter - Basic Principles
2.3 Working with the adapter - basic principles Risk of injury The Adapter must be positioned so that there is no danger of crushing. Load-carrying capacity Make sure that the nominal load of 52 kg is not exceeded when using the adapter with the seat support frame kg. Stable positioning The lifting equipment may only be used on a level, horizontal, solid floor. -
Page 12: Assembly 3.1 Assembly
3.1 Assembly 3.1.1 3.1.1 Follow the instructions in Chapter 3.1 of the owner’s manual 83 30 2 473 334 Seat support frame when setting up the seat assembly device. 3.1.2 Adjust the support arms of the seat bracket from the center of the laser etching so that they are 555 mm apart on the crossbeam and fasten them with a torque of 26 Nm. - Page 13 3.1.5 3.1.5 / 3.1.6 Place the seat rails of the seat on the support arms (see BMW workshop manual). Make sure that the seat is lying correctly on the seat support frame. Make sure that the seat is fastened correctly to the seat support frame and/or the accessories.
-
Page 14: Completing An Operation And Storing The Adapter
3.2 Completing an operation and storing the adapter 3.2.1 Check the adapter for any damage before and Always store the tool so that it is clean and safe. after each operation. Avoid contamination. Store the adapter as shown. Clean the adapter before storing it. -
Page 15: Troubleshooting
4.1 Troubleshooting Fault Problem Remedy Chapter Check scope of supply. Only use with the adapter provided. Adapter not correctly seated on the profile Adapter does not fit at the Observe the adjustment dimensions support frame points Only use the adapters with the seat approved for Arms not adjusted correctly the seat support frame Check scope of supply. -
Page 16: Regular Checking And Maintenance
4.2 Regular checking and maintenance The adapter must only be inspected by qualified personnel. The inspections must be carried out at least once a year. If the tool is used frequently, the inspections must be carried out at shorter intervals. Essentially, the inspections are visual and functional and are required to evaluate the condition of parts for damage, wear, corrosion or other changes and to make sure that the safety devices are complete and effective. -
Page 17: Service
5.1 Disposal Devices and machinery and components of devices and machinery must be disposed of in compliance with the laws, regulations and other stipulations of the country in which they are located. We recommend using specialist licensed companies for disposal. The modules and units have been developed to be environmentally compatible and suitable for recycling. -
Page 18: Declaration Of Conformity
EC Declaration of Conformity In accordance with EU Machinery Directive 2006/42/EC Tool type: Adapter Type designation: 83 30 5 A72 B58 Serial number range: 00001–10000 Developed and designed in compliance with the standards and guidelines listed below by the manufacturer: TKR Spezialwerkzeuge GmbH Am Waldesrand 9–11... - Page 19 Declaration of Conformity Tool type: Adapter Type designation: 83 30 5 A72 B58 Serial number range: 00001–10000 The product is developed and constructed in accordance with the UK legislation and designated standards by manufacturer: TKR Spezialwerkzeuge GmbH Am Waldesrand 9–11...
- Page 20 Am Waldesrand 9–11 D-58285 Gevelsberg (Germany) Other languages, accessories and Tel. +49 2332 66607-0 +49 2332 66607-941 spare parts: www.tkr-service.com E-mail info@tkrgroup.com Internet www.tkrgroup.com...
Need help?
Do you have a question about the 83 30 5 A72 B58 and is the answer not in the manual?
Questions and answers