Related Manuals for Precision E/One Extreme Series
Summary of Contents for Precision E/One Extreme Series
- Page 1 WH101F Installation Instructions & Warranty Information For Simplex Grinder Pump Stations Universal Wet Well and Integrated Ballast Design...
- Page 2 Environment One Grinder Pump Feature Identification 1. GRINDER PUMP BASIN – High density polyethylene (HDPE). 2. ACCESSWAY COVER – Painted steel, marine-grade enamel coated. 3. ELECTRICAL QUICK DISCONNECT (EQD) – Electrical lead from pump core terminates here (NEMA 6P). 4. POWER AND ALARM CABLE – Circuits to be installed in accordance with local codes. 5.
- Page 3 Figure 1 Overview of WH101F Station Installation FAILURE TO COMPLY WITH INSTALLATION INSTRUCTIONS WILL VOID WARRANTY...
- Page 4 The following instructions define the recommended procedure for installing the Model WH101F grinder pump station. The Model WH101F is a sewage-handling pump station and must be vented in accordance with local plumbing codes. Do not install the unit in locations classified as hazardous in accordance with the National Electric Code, ANSI/NFPA 70.
- Page 5 rocks, roots, and organic material, it may be an acceptable backfill. Such soil must be compacted in lifts not to exceed one foot to reach a final Proctor Density between 85% and 90%. Non- compactable clays and silts are not suitable backfill for this or any underground structure such as inlet or discharge lines.
- Page 6 connection must be tight or ground water will enter the station. c) Feed the wire through the length of conduit (contractor provided) which will protect it until it is below the 24” burial depth. d) Position the conduit vertically below the cable connector along the side of the station reaching down into the burial depth.
- Page 7 scale. Check the continuity between the following leads from the pump (tests should VALVE OPEN VALVE CLOSED be performed with the pump and alarm breakers inside the panel OFF): SLIDER VALVE SLIDER VALVE O-RING • Green/yellow (ground) to red (L1) SCH 80 PVC •...
-
Page 8: Lifting Instructions
Lifting Instructions FAILURE TO FOLLOW THESE INSTRUCTIONS COMPLETELY WILL VOID THE WARRANTY. Transporting unit to installation site: Always lift a unit from the bottom for the purpose of transportation. The station should be received attached to a pallet for this purpose. - Page 9 Grinder Pump Station Ballast Calculations and Assumption Any buried vessel that is submerged or partially submerged in water will be acted on by an upward buoyant force that attempts to return the vessel to a non-submerged state. The magnitude of this buoyant force is equal to the volume of the vessel that is submerged multiplied by the density of water.
- Page 10 TOP SOIL TO FINISHED GRADE BALLAST CONTRIBUTING CLASS I OR II BACKFILL MATERIAL TO TOP OF CORRUGATIONS STATION HEIGHT UNDISTURBED EARTH 6.0" Min GRAVEL 29.5 18.0" - 24.0" BEDDING MAX TANK DIAMETER Figure 8...
- Page 12 A Precision Castparts Company Environment One Corporation 2773 Balltown Road Niskayuna, New York 12309–1090 Voice: (01) 518.346.6161 Fax: 518.346.6188 NA0068P01 Rev E www.eone.com 2/24...
-
Page 13: General Information
User Instructions for the Environment One Grinder Pump General Information Your home is served by a low pressure sewer system; the key element is an Environment One grinder pump. The tank collects all solid materials and wastewater from the house. The solid materials are then ground to a small size suitable for pumping as a slurry with the wastewater. -
Page 14: Limited Warranty
E/One Sewers Limited Warranty For E/One Extreme D-Series, W-Series & Upgrade Environment One Corporation offers a limited warranty that guarantees its product to be free from defects in material and factory workmanship for a period of two years from the date of installation, or 27 months from the date of shipment, whichever occurs first, provided the product is properly installed,...