Westermann Table A Operation Manual
  1. Manuals
  2. Brands
  3. Westermann Manuals
  4. Indoor Furnishing
  5. Table A
  6. Operation manual

Westermann Table A Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operation Manual
Table A / Table A-Plus
electric
Version 02 – 2020.12
1/20

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Table A and is the answer not in the manual?

Questions and answers

Related Manuals for Westermann Table A

Summary of Contents for Westermann Table A

  • Page 1 Operation Manual Table A / Table A-Plus electric Version 02 – 2020.12 1/20...

  • Page 2: Table Of Contents

    Changes to the table frame or improper use can affect the safety, function and service life! These operating instructions are intended for the sit-stand tables of the motu furniture series A-Plus conference table with electrical height adjustment. Due to different designs / types, images may differ. Karl Westermann GmbH + Co. KG _______________________________________________________________________________________ Content INTENDED USE............................

  • Page 3: Intended Use

    INTENDED USE This sit-stand table may only be used as a temporary workstation in the professional sector. Modifications to the table frames are not permitted. This sit-stand table must be assembled, commissioned and functionally checked by competent personnel. The use of this sit-stand table for any purpose other than the aforementioned, e.g. as a lifting platform, seating, etc., is not permitted.

  • Page 4: General Safety Instructions

    Danger: Cleaning and user maintenance must not be carried out by children without supervision. Attention: Only use original accessories from Karl Westermann GmbH + Co. KG. The use of parts and components from third parties is prohibited! The use of unsuitable accessories may result in damage to or destruction of the table frame.

  • Page 5: Before Installation, Uninstalling Or Troubleshooting

    Attention: In the event of a malfunction (e.g. unintentional movement of the table top, e.g. if a button on the hand control gets stuck), please disconnect the mains plug immediately! Danger: Protect the table frame and especially all electrical components on the table frame from moisture, dripping and splashing water! Danger: In the event of a fault, the table top may move a little with each time you try to move it away.

  • Page 6: Before Operating

    When setting up, please note. • Uneven floors can be compensated for by means of the height adjusters on each foot. BEFORE OPERATING • Check that the operating voltage of the table corresponds to the local power supply. (see type plate on the control unit, standard = 230V). •...

  • Page 7: Important Service Note

    You can find a description of both on p. 17. Attention : No obstracles in The driving area! • When commissioning or if the table has been disconnected from the power supply for a long time, if there has been a malfunction at the table or if the connection between the drive and the control unit has been disconnected - the control unit of the table must be initialised, see p.

  • Page 8: Repairs

    REPAIRS In case of a technical defect on this unit, please contact a customer service authorised by us. The solution for simple possible error cases can be found in the section Error messages! Attention: To avoid malfunctions, all repairs must be carried out by authorised service personnel only.
  • Page 9 Special instructions: Please do not place sharp-edged objects or objects with abrasive surfaces on the finished surface to avoid unwanted scratches. Melamine resin-coated surfaces / HPL compact board Plastic-coated surfaces consist of resin-impregnated decorative papers and are characterised by very high wear resistance. Although liquids cannot penetrate the material, soiling or stains must be wiped away immediately.

  • Page 10: Assembly

    Special notes: Particularly in the post-oxidation phase, a "yellow cast" develops on linoleum. This is particularly noticeable in light colours, but disappears completely when exposed to UV light, and the linoleum reverts to its original colour. On the other hand, this "yellow cast" reappears if, for example, the surface of the covering is covered with monitors, mouse pads, etc.
  • Page 11 Wooden foot A/A-Plus The version of the table base A or A-Plus with attached wooden base is already fully assembled. No further work step is necessary here. Foot A in wood Foot A-Plus in wood 2) Wiring the truss To wire the sit-stand table, proceed as follows: 1) Adjusting the crossbar length As a rule, we already adjust the length during production.
  • Page 12 2) Connections to the motor control unit Attention: Do not plug in the power supply cable/mains cable until all other electrical connections have been made! (All motors, the hand control and possibly other accessories are connected to the control). To put the sit-stand table into operation, proceed as follows: 2) Connect drives Make sure that the connection cables of the drives reach from both sides to the corresponding connection of the control unit.
  • Page 13 4) Connecting the power supply cable / mains cable Attention: Before connecting the power supply cable, check again that the mains voltage corresponds to the type plate of your control unit and that all components are connected to the correct sockets. The motor control unit is ready for operation when the power supply cable is plugged in! Note: When connecting the power supply cable/mains cable for the first time, it is necessary to initialise the table frame (RESET), this is described in section...
  • Page 14 Then mount the panel support to the crossbar with the M8 screws according to the frame drawing through the threads in the installation column. The max. tightening torque for these screws is 10 Nm. Optional CPU holder: Then mount the plate carrier and CPU holder to the crossbar with the M8 screws through the threads in the built-in column as shown in the frame drawing.

  • Page 15: Operation

    5) Assembly of the manual switches Now mount the handset on the table top using the fixing material supplied (screws in a labelled bag). Holes or screw points are provided for this purpose on the handset and in the top. Stick the cable clip onto the table top and thread the cable in.
  • Page 16 INITIALISATION / RESET After assembly, or if the table has been disconnected from the power supply for a period of time and there has been a malfunction with the table; or if the connection between the drive units and the control unit has been disconnected – the control unit of the table must be initialised. If the control unit requires a fresh initialisation, only the downward movement of the table, with a reduced speed, is possible.

  • Page 17: Troubleshooting

    To deactivate a container or shelf stop position, proceed as follows: • Move the sit-stand table to any position in the lower half of the travel range to deactivate the container stop or to the upper half of the travel range for the shelf stop position.

  • Page 18: Click Codes Of The Control Unit

    CLICK CODES OF THE CONTROL UNIT As soon as power is supplied to the motor control unit, the control unit uses the built-in relays to inform the user acoustically about the system status; and in addition, informs about the reason of the last shutdown.

  • Page 19: Tests And Certificates

    TESTS AND CERTIFICATES The drive system is tested according to: Electromagnetic Compatibility (EMC Directive 2014/30/EU). • EN 61000-6-2:2005 Electromagnetic Compatibility (EMC) • EN 61000-6-3:2007 + A1 Electromagnetic compatibility (EMC) • EN 61000-3-2:2006 + A1 + A2 Electromagnetic compatibility (EMC) • EN 61000-3-3:2008 Electromagnetic compatibility (EMC) Electrical safety (Low Voltage Directive 2014/35/EU) •...

  • Page 20: Contact

    CONTACT Version 02 – 2020.12 20/20...

This manual is also suitable for:

Table a-plus

Table of Contents