Advertisement
Quick Links
Advertisement
Related Manuals for Ascent ACT AON1200D
Summary of Contents for Ascent ACT AON1200D
- Page 1 ACT AON1200D Optical Receiver Quick Reference Guide Revision A...
- Page 2 Quick Reference Guide Revision A Copyright © 2023 Ascent Communication Technology Limited. All rights reserved. Reproduction in any manner whatsoever without the express written permission of Ascent Communication Technology is strictly forbidden. This document is produced to assist professional and properly trained personnel with installation and maintenance issues for the product.
- Page 3 AON1200D Smart Optical Receiver Table of Contents 1 Product Summary ........................4 2 Performance Characteristics ....................4 3 Safety instructions ........................4 4 Technical Specifications ......................5 5 Block Diagram ........................6 6 Structure Description ......................6 7 Installation ..........................6 8 Function Display and Operating Instruction ................
- Page 4 AON1200D Smart Optical Receiver Ascent’s AON1200D outdoor optical receiver is our latest 1GHz dual-way switch optical receiver. With wide range receiving optical power, high output level, low power consumption. It is the ideal equipment to build the high-performance NGB network.
- Page 5 AON1200D Smart Optical Receiver Technical Item Unit Item Parameters Optical Parameters Receiving Optical Power -9 to +2 Receiving Optical Power +2 to -9/-8/-7 Optical AGC Control Range Optical AGC Control Range (adjustable) Optical Return Loss >45 Optical Return Loss Optical Receiving Wavelength SC/APC or Optical Connector Type Optical Connector Type...
- Page 6 AON1200D Smart Optical Receiver 1. Fix the optical receiver and connect the ground wire. 2. Loose the cover screw and open the cover. 3. Make sure the receving power in the proper value. 4. Connect optical fiber, Ethernet cable and RF coaxial cables. 5.
- Page 7 AON1200D Smart Optical Receiver Mode: Mode selection button, total thirteen modes. Press the mode selection button to enter the corresponding status display, thirteen modes to cycle. The following is the detailed instructions: Solutions Provider for FTTx, RFoG, and HFC www.ascentcomtec.com Page 7 of 15...
- Page 8 1. Opening the IE browser and entering the equipment default IP address 192.168.1.168 leads to the following interface: 2. Enter the user name admin and password ascent, to show the following interface: This is the Device parameters: Display and configuration menu.
- Page 9 AON1200D Smart Optical Receiver 3. Common Parameters: Describes the common parameters such as S/N, model type, MAC address, temperature and so on. 4. Trap parameters interface: Describe the setting of the alarm destination address. Solutions Provider for FTTx, RFoG, and HFC www.ascentcomtec.com Page 9 of 15...
- Page 10 AON1200D Smart Optical Receiver 5. Network parameters interface: Describes the IP, gateway and subnet mask parameters and so on. 6. Change password interface: Change the login password in this interface. Solutions Provider for FTTx, RFoG, and HFC www.ascentcomtec.com Page 10 of 15...
- Page 11 AON1200D Smart Optical Receiver 7. Alarm Logs interface: Display relevant logs in this interface. 8. Update interface: Update the firmware if necessary in this interface. If users configured the network management transponder, need to do the following settings: Transponder IP setup instruction: Network management directly modify: 1.
- Page 12 AON1200D Smart Optical Receiver 4. Enter new IP address, gateway and subnet mask. 5. Click modify, then exit, it is done. There will show new IP address and gateway on operational logbook. 6. Reboot the transponder, the new IP take effect (Click the reboot button in the network management software or power on again) Solutions Provider for FTTx, RFoG, and HFC www.ascentcomtec.com...
- Page 13 AON1200D Smart Optical Receiver Failure phenomenon Failure cause Solution After connecting the network, 1. The optical input power of 1. Check the optical input power and make the image of the optical the optical receiver is too appropriate adjustments to make it in the contact point has obvious high, make the output level of specified range;...
- Page 14 AON1200D Smart Optical Receiver contact points appear one or bad earth of equipment or has been reliably grounding and the two horizontal bright traces. power supply. grounding resistance must be﹤4Ω. After connecting the network, The optical fiber connector 1. Check the type of optical fiber connector the received optical power of types do not match, maybe and adopt the APC type optical fiber...
- Page 15 Phone: +84 243 795 5917 WEB: www.ascentcomtec.com EMAIL: sales@ascentcomtec.com Specifications and product availability are subject to change without notice. Copyright © 2023 Ascent Communication Technology Limited. All rights reserved. Ver. ACT_AON1200D_Optical_Node_QRG_V1a_Oct_2022 Solutions Provider for FTTx, RFoG, and HFC www.ascentcomtec.com Page 15 of 15...
Need help?
Do you have a question about the ACT AON1200D and is the answer not in the manual?
Questions and answers