Advertisement
Quick Links
Advertisement
Related Manuals for ICI FMX 300X P Series
Summary of Contents for ICI FMX 300X P Series
- Page 1 Edit Text Industry FMX 300X P-SERIES QUICK START GUIDE ICI cameras fall under US Federal Law and Export Control. 2105 W. Cardinal Dr. Beaumont, TX 77705 Phone: (409) 861-0788 Toll Free: (866) 861-0788 infraredcameras.com support@infraredcameras.com We Are IR ™...
- Page 2 IN NO EVENT SHALL ICI BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF ICI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
-
Page 3: Package Includes
Package Includes Waterproofing Kit FMX 300X Anchors x3 Alignment Guides Screws x3 Memory Card Hex Wrench ENSURE ALL SYSTEM EQUIPMENT AND COMPONENT ITEMS ARE PRESENT BEFORE BEGINNING INSTALLATION... -
Page 4: Installation
Installation USE THE ALIGNMENT GUIDES TO DRILL HOLES FOR SETTING DEVICE SCREWS. DO NOT USE TOO LONG SCREWS WHEN INSTALLING THE DEVICE. USING SCREWS THAT ARE TOO LONG MAY DAMAGE THE THERMAL CAMERA. THE INSTALLATION WALL SHOULD BE ABLE TO BEAR AT LEAST 4 TIMES THE WEIGHT OF THE CAMERA AND INSTALLATION ACCESSORIES. - Page 5 Place the alignment guide on Insert the expansion screws the mounting position and into the drilled holes. drill three Φ5 mounting holes according to the markers on the alignment guide. The recommended depth is 25mm. Open a φ 36 hole with “A” Pass the tail wire of the camera as the center of the circle through the A hole, then use...
- Page 6 Wall Mounting Ceiling Mounting IF THE INSTALLATION SITE IS A CONCRETE WALL OR CEILING, FIRST INSTALL EXPANSION SCREWS; THEN, INSTALL THE BRACKET. THE INSTALLATION HOLES OF THE EXPANSION SCREWS NEED TO BE IN LINE WITH THE BRACKET. IF THE INSTALLATION SITE IS A WOODEN WALL, USE SELF- TAPPING SCREWS TO INSTALL THE BRACKET DIRECTLY.
- Page 7 WHEN USING THE CAMERA, INSTALL THE WATERPROOFING KIT TO PREVENT WATER FROM ENTERING THE NETWORK CABLE. Pass the network cable Place the rubber ring on the through the fastening nut network cable between the and the main body of the main body of the waterproof waterproof cover.
- Page 8 IN ORDER TO ENSURE THE NETWORK SECURITY OF THE CAMERA, IT IS RECOMMENDED IT CONDUCT REGULAR NETWORK SECURITY ASSESSMENT AND MAINTENANCE OF NETWORK SYSTEMS. Insert the waterproof rubber ICI recommends having a ring into the main body of the service professional connect waterproof cover. Turn the...
- Page 9 Use the Hex Wrench to loosen the lock nuts indicated and adjust the angle of the device by turning or rotating the device. Tighten the lock nuts when device is properly aligned. 0° to 360° Horizontal Pan 0° to 90° Tilt Adjustment 0°...
-
Page 10: Alarm Interface
Alarm Interface The camera can be connected to alarm switch signal (0~DC 5V) input and switch output (no voltage). An external power supply is required when connecting the alarm. The specific wiring method is shown in the figure below. -
Page 11: Memory Card
Memory Card Use a standard screwdriver Insert the Micro-SD Card into the to detach and remove the top of the device until a clicking memory bay cover. sound is heard. Use a standard screwdriver replace and the memory bay cover and screws. - Page 12 Website: www.infraredcameras.com You may reach a representative by phone or email Mon – Fri 8:00AM - 5:00PM CST. ICI manufactures complete systems and software. We can provide complete engineering, software, and OEM solutions. Our Fortune 500 clients rely on us for infrared equipment and thermography training (which we offer through the Infrared Training Institute).