SAL PIXIE PC152V/R/BTAM Quick Start Manual

PIXIE Smart 0/1-10V
Controller
PC152V/R/BTAM
1. Foreword
IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE GUIDE AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
DIY
SAL products are designed in accordance with all mandatory International and Australian Standards, which require installation in accordance with
AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equipment. Products are sold in accordance with the following
instructions and SAL standard terms and conditions of sale, available via www.sal.net.au.
Due to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performance
guarantee unless expressly confirmed in writing by SAL at the time of order. The product wireframe drawings in this document are intended for illustration purposes
only and may differ from the final physical product. The installation instruction is subject to change without prior notice.
2. Product Introduction
The PIXIE 0/10-10V Controller is designed to control devices that accept 0-10V or
1-10V control signals, typically 0/1-10V dimmable LED drivers, 0/1-10V dimmable
ballasts etc, allowing users to dim* and operate ON/OFF the connected lighting,
with the PIXIE Apps and ecosystem products.
2.1 Product Features
• Outputs 0-10V control signal
• In-built relay as optional control method
• PUSH DIM function allows control with a momentary switch
• Memory function restores the last state (on/off/dim level) of the lights from a
power outage
• One in-built set button, for easy testing and commissioning
• One LED indicator to reflect working status
2.2 The package includes
• PIXIE Smart 0/10-10V Controller * 1
• Quick Start Guide * 1
3. Specifications
Model NO.
PC152V/R/BTAM
Relay rating
Operation Ambience
-10 ~ 40
Temperature (˚C)
Storage Ambience
0 ~ 60
Temperature (˚C)
Storage Humidity
10% - 85% RH, NC
4. Installation and Wiring
4.1 Preparation
-Set the DIP switches at desired position
-Make sure the loads are compatible
(0/1-10V dimmable) and within the rating
4.2 Installation (Licensed Electrician Only)
1. Disconnect power supply
2. Wire the product as per the wiring
diagram on the right***
3. Supply power to the circuit
4. Make sure the LED indicator is lit, then
press the Set button to test the control,
single press to turn ON/OFF, long press to
change brightness
*** The relay output (LOAD terminal) is highly recommended for connecting & disconnect-
ing power to the 0/1-10V drivers for best control performance, even though it's optional.
Power Input
Resistive load Max. 5A
0-10V Output
LED Max. 2.5A
Operation Humidity
Dimension (mm)
Active
Neutral
Momentary
switch
(optional)
Quick Start Guide
Version
Date
2.3 Product illustration**
Power Input
Terminals
Relay Output
Terminals (optional)
Terminals for momentary
switch control (optional)
220-240V~ 50Hz
20mA (Up to 10 drivers)
IP Rating
IP20
10% - 85% RH, NC
145 x 47 x 16
PIXIE SMART 0/1-10V CONTROLLER
A
PC152V/R/BTAM
Dip Switch
N
1-Memory
Power input: 220-240V ~ 50Hz
2-Relay
Relay output: Max 5A
N
0.75-1.5mm
0/1-10V output: 20mA (Source)
LOAD
Ta:-10℃-40℃
4-5mm
(Optional)
µ
PUSH DIM
S
A S
N N
N
MADE IN CHINA
Wiring diagram
1/2
1.0
15/12/2023
145 mm
Set button
LED Indicator
*The dimming performance (dimming curve,
dimming depth, smoothness etc.) is subject to the
0/1-10V driver/ballast design, and this, is expected
to vary among different drivers/ballasts.
**All drawings shown are for illustration purpose
only, actual product may vary due to product
enhancement.
Set
ON
1 2
ON ON
0/1-10V driver
OFF
1 2
2
0/1-10V DIM+
DIM+
0/1-10V DIM-
DIM-
0/1-10V DIM+
DIM+
0/1-10V DIM-
DIM-
0/1-10V driver
0/1-10V DIM+
0/1-10V DIM-
0/1-10V driver
MASTER MASTER
DIP switches for Memory
and Relay functions
ON
1 2
0-10V control
signal output
A
N
A
N
A
N