Advertisement
Quick Links
2005 – 2015 Toyota Tacoma Rear 2" Receiver Bumper w/ D-Ring Mounts
Kit Contents:
Item
Rear Bumper
M12 x 1.25 x 40mm Hex Bolt
Large M12 Flat Washer
Lock Washer for M12 Hex Bolt
Rubber Trim
Rear Storage Box Cover
Rear Storage Box Lock Mechanism
Installation Instructions:
1. Before you start, you must remove the factory rear bumper. These instructions cover the removal of the bumper
and OEM tow package (if equipped) together as a single assembly. If you
prefer, you may remove the two items separately. (Figure 1)
2. Begin by removing lights from both sides of the license plate. From behind
the bumper locate each light. Twist 90 degrees and pull to remove the bulb
and socket from the housing.
Remove these bolts
4. Use a 17mm socket to remove the bolts on either side that
attach the bumper frame mount to the frame (keep these
bolts, you will re-use them later). Do not fully remove the
forward most bolt, it only needs to be loosened to allow the
bumper to slide out the rear and will help position the
Warrior bumper during installation. There will be only
three bolts per side without the OEM Receiver, or five bolts
per side with the OEM Receiver (Figure 3).
3. Disconnect the trailer connector plug
and mounting plate (if applicable) by
removing the two bolts at the top of the
plate that attach the plate to the OEM Receiver cross beam (Figure 2). If
you find that you need to disconnect the wiring harness from the plug, the
factory connection will have a plastic plug with a retainer. The retainer
must "swing" open approximately 90 degrees to release the connection.
Tuck the harness and connector plug safely to the side so that it does not
Figure 2
get damaged during the install.
●
P/N 4560
Qty
Item
1
Filler Plate / Light mount Bracket
4
¼" x ¾" Carriage Bolt
4
¼" SAE Washer
4
¼" Nyloc Nut
36"
¼" x ¾" Hex Bolt
1
Plastic License Plate Nut
1
#14 x 1" Self-Tapping Screw
Figure 3
●
11100 SW Industrial Way
Phone: (888) 220-6861
customerservice@warriorproducts.com
www.warriorproducts.com
Figure 1
OEM Receiver
only
●
Warrior Products, Inc.
Tualatin, OR 97062
Fax: (503) 692-0364
Qty
2
4
8
8
4
4
4
Advertisement
Related Manuals for Warrior Products 4560
Summary of Contents for Warrior Products 4560
- Page 1 Warrior Products, Inc. 11100 SW Industrial Way Tualatin, OR 97062 Phone: (888) 220-6861 Fax: (503) 692-0364 customerservice@warriorproducts.com www.warriorproducts.com 2005 – 2015 Toyota Tacoma Rear 2” Receiver Bumper w/ D-Ring Mounts P/N 4560 Kit Contents: Item Item Rear Bumper Filler Plate / Light mount Bracket M12 x 1.25 x 40mm Hex Bolt...
- Page 2 Bolts in place (Figure 4). 7. Install Filler Plates / Light Mount Brackets into your Warrior Products bumper with the supplied ¼” carriage bolts and associated hardware. (This can be done with bumper installed, but it is easier to do it at this time).
- Page 3 Mount your lights in the holes that you have drilled and wire as desired. 8. Carefully position your new Warrior Products bumper on your truck, this is also where and extra set of hands will be very helpful. Slide the open slots of the frame mounting plates over the existing partially threaded Front Bolts that were left in during the removal of the OEM bumper.
- Page 4 Warrior Products, Inc. 11100 SW Industrial Way Tualatin, OR 97062 Phone: (888) 220-6861 Fax: (503) 692-0364 customerservice@warriorproducts.com www.warriorproducts.com 14. Assemble your Rear Storage Box Cover and Locking Mechanism. a. Slide the supplied round gasket over the threads of the lock and place against the mounting flange.