Table of Contents
Advertisement
Quick Links
S
Y
S
T
E
M
M
A
N
U
A
L
N
U
A
L
S
Y
S
T
E
M
M
A
E
M
M
A
N
U
A
L
S
Y
S
T
TSI Manual Bypass Rack 10A -1U
T306730006
TSI_MBP Rack_10A_ User Manual_Rev0- -17.01.13
This document is subject to modification without prior notice from the manufacturer.
The present equipment is protected by several international patents and trademarks.
Advertisement
Table of Contents
Related Manuals for CE+T Power TSI T306730006
Summary of Contents for CE+T Power TSI T306730006
-
Page 1: System Manual
TSI Manual Bypass Rack 10A -1U T306730006 TSI_MBP Rack_10A_ User Manual_Rev0- -17.01.13 This document is subject to modification without prior notice from the manufacturer. The present equipment is protected by several international patents and trademarks. -
Page 2: Table Of Contents
Tables of contents SYSTEM MANUAL ..............1 0 Safety Recommendations ............... 3 1 Introduction ..................4 1.1. Overview: ............................4 1.2 Product Description: ........................4 2 Product Constitution ................ 6 2.1 TSI MBP Rack Identification Plate ....................6 2.2 Package Includes .......................... 6 3 Installation .................. -
Page 3: Safety Recommendations
0 Safety Recommendations Your safety is our major concern. Read carefully all safety aspects listed in this manual prior any intervention on the appliance. The manufacturer declines all responsibilities if equipment has not installed by skilled technician and in a proper way according to local safety regulation and as it is described herein. TSI Manual Bypass Rack is not supplied with internal disconnect devices. -
Page 4: Introduction
1 Introduction This document applies to the TSI System. For product description, please refer to related document. The information provided in this manual covers single phase Manual Bypass Rack 10A 1U Unit, their basic functions, operating procedures, options available. It also includes information on electrical connections, cabling, mechanical installation, Commissioning and troubleshooting the equipment. - Page 5 The MBP unit provides an isolation path of power for Inverter system for preventive maintenance or service. There are both normal and Bypass modes of operation as described as below 1. Under normal operation, the Mains AC Input flows through the MBP unit to the Inverter/UPS and then out to the Connected Loads.
-
Page 6: Product Constitution
2 Product Constitution Please check that operating manual version you are reading is corresponding to TSI version running in your installation. TSI Manual Bypass Rack for the Bypass of UPS/TSI Inverter. Part Description and Number: Manual Bypass Rack 10A – 1U T306730006 2.1 TSI MBP Rack Identification Plate 2.2 Package Includes... -
Page 7: Installation
3 Installation Caution: Installation and commissioning must be done and conducted by trained people fully authorized to act on installation. 3.1 Overview The Manual Bypass Racks are foreseen to be recessed into an electrical cabinet of 19” standard. 3.2 System dimensions The picture shows the front, side and rear view of the MBP Rack. -
Page 8: Fixing
SIDE VIEW REAR VIEW 3.3 Fixing A full range of accessory is ready made to allow easy integration of the TSI MBP in almost any kind of standard cabinets. Among other we provide fixing set for: • 19” – 600mm depth cabinets (most standard solution, which is supplied by default) •... -
Page 9: Wiring
3.4 Wiring Caution: The TSI MBP Rack does not include any protecting and/or disconnecting devices on AC input. Before any intervention on the TSI MBP Rack, operator has to make sure that power is removed from AC input mains. All breakers, cables and wires must be CE and classified for min 90°C (194°F) operation All DC cables and alarm cables as well must be kept minimum 10mm away AC cables... -
Page 10: Ac Input Connection
3.4.1.1. AC Input Connection IEC Plug EMO-40 available along with the MBP kit should be used by the customer to connect the AC mains input. IEC Socket is available in the rear panel. Refer the below table for wire size. Description AC breaker Cable size... -
Page 11: Tsi Input/Output Connection
3.4.1.3. TSI Input/Output Connection For the Y-1 Modules to be connected on the MBP Rack, wires are provided with cable markers for direct connection. Refer the below table for wire colour & size. Description Cable colour Cable size Identification No Cable kit TSI Lin Brown... -
Page 12: Use Of Manual Bypass
4 Use of Manual Bypass The manual by pass operates via manually operated switches that create a by-pass from mains input via output AC distribution. Inverter modules are by-passed and possible to remove without impacting the load. When in by-pass modules have no AC supply, DC is still present. The manual by-pass is “Make before Break”... -
Page 13: Troubleshooting
MBP OFF :(Disengaged) 1. Check that both AC input and output breakers are switched off. 2. Check that maintenance by-pass switch, is in position “MBP ON sequence” 3. Switch ON DC power -Inverter starts up initially 4. Switch ON the AC input Breaker. Output of MBP is available with this main input supply. 5. -
Page 14: Commissioning
6 Commissioning Caution: Installation and commissioning must be done and conducted by trained people fully authorized to act on installation. It is prohibited to perform any isolation test without instruction from manufacturer. Care must be taken to prevent dust, which can damage electronic components, by reducing the ESD distances. -
Page 15: Commissioning
Inverter module are correctly installed and fixed into the rack Inverter cabinet is correctly connected to EARTH Neutral N is connected to EARTH (If required!) Check or turn OFF manual by pass switch S1 6.2 Commissioning Unplug all inverters except one inverter per phase (Just pull off the inverter from the shelf, to interrupt electrical contacts) Check the commercial AC before close breaker .Switch ON the commercial AC Turn S1 to OFF Position Manual by-pass... -
Page 16: Technical Data Sheet
7 Technical Data sheet NVIRONMENT ENERAL <1500m Connection I/O IEC connector Altitude above sea Protected against inversion of polarity n x 1500VA -20 to 50 °C Ambient temperature (**) Pmax at 100% LOAD Enclosure IP20 Derating up to 65°C -40 to 70 °C Storage temperature AC I NPUT... -
Page 17: Schematic Drawing
8 Schematic Drawing...