Advertisement
Quick Links
LIMITED WARRANTY
Ascend II Bases are warranted from the original purchase date to the original purchaser for normal commercial usage - defined as a standard forty-hour work
week according to the below-listed schedule and limitations.
• 5 year warranty on dual-motor bases
• 3 year warranty on single-motor bases
Warranty Exclusions
This warranty will not cover labor, freight, or damage from misuse, abuse, negligence, alteration, assembly, installation, attachments, accident, vandalism,
acts of nature or any other event beyond our control. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damage is excluded. The user assumes all risk of injury resulting from use of this product.
This warranty applies only to products purchased through authorized dealers and products sold within the United States of America and the Commonwealth of
Canada. This warranty does not apply to products used for rental purposes. This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
© Office Star Products May, 2023
A2EB322 / A2EB222
ASCEND II HEIGHT ADJUSTABLE BASE
OPERATING INSTRUCTIONS
WARNING
1.
2.
3.
4.
5.
6.
IMPORTANT
Base must be reset before operating.
See page 5.
Do not use this product unless all bolts, screws and knobs
are securely tightened.
Check that all bolts, screws and knobs are tight every three
months or as needed.
Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
Do not use product as a stepladder.
Use this product for its intended purpose only.
Use mild detergent only for cleaning.
Page 1
Advertisement
Related Manuals for OSP ASCEND II A2EB322
Summary of Contents for OSP ASCEND II A2EB322
- Page 1 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE OPERATING INSTRUCTIONS IMPORTANT Base must be reset before operating. See page 5. WARNING Do not use this product unless all bolts, screws and knobs are securely tightened. Check that all bolts, screws and knobs are tight every three months or as needed.
- Page 2 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE ASSEMBLY INSTRUCTIONS PART A. Center Trunk ......1 B. Column ......2 C.
- Page 3 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE ASSEMBLY INSTRUCTIONS STEP 2 STEP 3 STEP 2 Fasten Columns (B) to Side Supports (C) and Center Trunk (A) using eight Bolts (F). LOOSELY TIGHTEN BOLTS (F) USING 4MM ALLEN KEY (J4). STEP 3 Run Handset (E) cable through hole below Center Trunk (A) and connect cable to Control Box, located in Center Trunk (A).
- Page 4 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE ASSEMBLY INSTRUCTIONS STEP 4 STEP 5 STEP 4 Secure assembly to worksurface using twenty four Screws (G) as shown. Secure Handest (E) to desk top using two Screws (H). FULLY TIGHTEN ALL SCREWS USING PHILLIPS SCREWDRIVER (not provided). IMPORTANT: AT THIS POINT, PLEASE FULLY TIGHTEN ALL SCREWS FROM THE PREVIOUS THREE STEPS.
- Page 5 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE OPERATING INSTRUCTIONS IMPORTANT You must reset the Control Box, using the handset as shown below, prior to use. Plug Power Cable (K) into wall outlet. Press and Hold the up/down buttons for more than 3 seconds: LED Screen will read “SET”.
- Page 6 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE OPERATING INSTRUCTIONS Page 6...
- Page 7 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE OPERATING INSTRUCTIONS Page 7...
- Page 8 A2EB322 / A2EB222 ASCEND II HEIGHT ADJUSTABLE BASE OPERATING INSTRUCTIONS...