Sekonda ALPINE 30180 Instructions

SEKONDA ALPINE SMART WATCH INSTRUCTIONS
(30180)
Charging
Power on
Heart Rate sensor
Return key
CHARGE YOUR SMART WATCH
- Connect and charge your watch using the magnetic USB cable provided.
- Your smart watch should be charged for two hours before using it for the first
time.
- When connected to the charger, the watch will automatically turn on. This may
take up to a minute when the battery is fully depleted.
TURN ON YOUR SMART WATCH
- Press and hold the top button for 5 seconds to turn your smart watch on.
- Remove the printed screen protector. Below this is an additional screen
protector. It is advised that you keep this on your watch to protect it from wear
and tear.
- When started for the first time, the Device Information will be displayed.
- Swipe left to view the QR code which you can scan to download the InfoWear
app.
DOWNLOAD AND INSTALL THE APP
- To download the app please search for "InfoWear" in the app store on your
phone.
- Or scan the QR code using your smartphone camera or QR code reader app.
The InfoWear app will work on the following smartphones:
Android (version 5.0 and above)
Apple iOS (version 10.0 and above)
CONNECT YOUR SMART WATCH TO THE APP
- Open the app and accept the permissions.
- Select your region (e.g. "U.K")
- Either create an account or select "Login without account".
- On the next screen you can enter your personal information and goals such as
your step count target.
- The app will then prompt to search for devices to connect to.
- Your watch has a unique Bluetooth name beginning with "G18" followed by
letters and/or numbers. You can view the Bluetooth name of your watch listed
in the Device Information shown on the screen when you first turn your smart
watch on.
- Select the correct Bluetooth name from the list to connect to your smart
watch.
- The watch will display the correct time after pairing is successful.
SYNCHRONISE DATA WITH THE APP
- After your watch is paired with the app you can synchronise data the watch
has recorded.
- Please sync your app daily to avoid loss of recorded data. Data on the watch
is reset at midnight every day.
- To sync your data, connect to the app. On the home screen, swipe down to
sync data with the watch. "Data syncing" will be displayed at the top of the
page.
SET UP
On your smart watch:
- Swipe up from the home screen and tap the cog.
- Select "Brightness" to set the screen brightness.
- Select "Vibration intensity" to set the strength of the vibration that will be
used for notifications.
- Swipe up to view the next section of the menu and select "Auto lock" to set
how long the screen will stay on for. The screen can be set to stay awake for
a maximum of 20 seconds. Turn on "Raise to wake" to have the screen turn
on when you turn your wrist.
ON THE INFOWEAR APP:
SET THE LANGUAGE
- Tap on "Device" at the bottom of the app screen.
- Then tap on "device management".
- Next to the Bluetooth name, tap on "Enabling" > "More settings" > "Device
language selection".
- Available languages are English, Simplified Chinese, French, German, Italian,
Spanish, Russian, Polish, Portuguese, Hindi, and Japanese.
SET WHICH NOTIFICATIONS YOU WOULD LIKE TO RECEIVE ON YOUR WATCH
- Tap "Device" at the bottom of the screen.
- Tap "Message notification settings" and tap the "Master switch" to accept
the permissions for the app to access your notifications. This function can
not be used without accepting the permissions.
- On this screen you can set which apps you would like to receive notifications
from on your smart watch, as well as incoming calls, messages, and missed
calls.
- If you are using an android phone tap "Third-party app" to select which apps
you would like to receive notifications from.
OTHER SETTINGS
- Reminder settings
- Alarm reminder – Set up to 5 alarms that will cause the smart watch to
vibrate at the set time.
- Sedentary alert – Set an alert to remind you to get up and walk around –
the smart watch will vibrate at the set intervals.
- Drink water reminder – The smart watch will vibrate at the set intervals.
- Medication reminder – The smart watch will vibrate at the set intervals.
- Continuous Heart Rate Monitoring – You can set your smart watch to
continuously monitor your heart rate (please note, this will greatly reduce the
battery life). You can also set a "Heart rate warning" to notify you when your
heart rate exceeds the set rate.
- Weather settings – Turn on/off "Weather sync" for your smart watch to
display up-to-date local weather.
- Shake to take photos – Use your smart watch as a remote shutter for the
camera on your smart phone.
- App, open the InfoWear app and tap on "My" at the bottom of the screen.
- Tap on "Data authorization", then "Strava". Tap the switch to
authorize data sharing with Strava.
For the app to function correctly please take notice of the following:
- Do not pair the watch directly with the Bluetooth in your phone's
settings. Always pair the watch through the app.
- Do not turn off Bluetooth in your phone's settings.
- If you would like to receive notifications from the app, you must
accept the app's permissions.
USING YOUR SMART WATCH
THE SMART WATCH INTERFACE
- The screen will turn on when you turn your wrist, or by pressing one of the
buttons.
- The home screen of the watch with the time will be displayed.
- Swipe to the left or right from the home screen to cycle through the
watch function screens – heart rate, blood oxygen, sleep tracker,
weather, music control, calorie and step counter.
- Press the top button while on the home screen to enter the main
menu. From here you can access the following – Workout, Activity,
Stats, Heart rate, Blood oxygen, Sleep, News, Weather, Music Control,
Stopwatch, Timer, Find phone, Breathing, and Settings.
- Swipe down from the home screen to view your notifications.
- Swipe up from the home screen to view a menu where you can access
the following settings:
- Vibration intensity – set the intensity of the vibration of the watch.
- Sun symbol - "Wake for 5 mins" – The screen will stay on for 5 mins.
- Padlock symbol - Lock screen – The screen will be locked – hold the
top button down for 5 seconds to unlock.
- Moon symbol – Turn on 'Do Not Disturb' mode. No notifications will
be received.
- Battery symbol – Turn on power saving mode – The watch will not receive
notification messages and the brightness of the watch will be the lowest
setting.
- Cog symbol – further settings – Watch faces, Brightness, Vibration intensity,
Auto lock, System Settings, QR code, About.
BUTTONS
- Pressing any of the buttons will wake up the screen.
- Within any menu, press the top button to go back, or press the bottom button to
return to the home screen.
- To turn your smartwatch on or off hold the top button down for 5 seconds and
select "Power off".
CHANGING YOUR WATCH DIAL STYLE
- On the home screen (the screen displaying the clock) of your watch, press and
hold on the middle of the screen.
- Swipe left to choose a dial style and tap to select it.
DOWNLOADING MORE DIAL STYLES
- Open the app and tap "Device" at the bottom of the screen.
- Tap on "Dial center", then "Online dial". Here you can view the available dial
designs.
- To select a dial and add it to your watch, tap it and then tap "Sync dial".
- Make sure your watch is close to your phone. The app will display
"Transmitting..." for a few seconds while data is transferred, then the dial
will be installed on the smart watch.
- The new dial will then be displayed on your watch.