Introduction And Specifications - U.S.SAWS MC-800 Operating Manual

I N T R O D U C T I O N & S P E C I F I C AT I O N S
1.0 INSTRUCTIONS FOR USE OF MANUAL SECTIONS
Section
Table of Contents & Introduction ..................................................... 2
Symbols & Decals ................................................................... 3
Safety Instruction ................................................................... 4 - 5
Pre-Operation Checklist ..............................................................6 - 8
Operation ................................................................... 9 - 10
Parts Breakdown ............................................................. 11 - 13
Maintenance & Inspection .................................................... 14 - 15
Propane Power System .................................................... 16 - 46
Warranty & Service ............................................................. 47 - 48
Foreword/Introduction
The owner's manual is intended to point out some of the basic safety situa-
tions that maybe encountered during the normal operation & maintenance
of the MC-800 Machine & to instruct you in safety practices for dealing with
these conditions. Keep all manuals provided with your
machine in a safe place at all times.
The information and specifications included in this publication were
in effect at the time of approval for printing. U.S.SAWS reserves the right,
however, to discontinue or change specifications or design at any time with-
out notice and without incurring any obligation.
The MC-800P "Joint Hog" is a Milling machine designed to remove up to 4"
in width and 1-3/4" in depth of concrete to repair spalled joints. It can also
be used for grooving, cutting inlays, and to prep for permanent line striping
in floors. The blade rotates in an upward direction allowing for easy dust
collection when connected to an appropriate vacuum system. The machine
should always be operated with a dust collection system and in a well-venti-
lated area due to carbon monoxide fumes emitted from the gasoline engine.
Features:
Powered by a "certified" Propane 16 HP Vanguard V-Twin engine with
•
an electric start and a C02 monitor
• Built on the U.S.SAWS JS Series frame
• Frame is fully box welded of high-quality heavy gauge steel
• Solid rear axle serves as the chassis' lifting pivot point for a nearly
indestructible platform
Page
Surface Prep
Division
Read this entire operations and maintenance manual before using your new
tool. Pay close attention to the Rules for safer operation,
Dangers, Warnings and Cautions.
The purpose of safety symbols and explanations are to attract your atten-
tion to possible hazards and how to avoid them. The safety symbols and
explanations do not by themselves eliminate any danger. The instructions
or warnings they give are not substitutes for proper accident prevention
measures.
DANGER: Indicates an imminently hazardous situation that if not avoided,
will result in death or serious injury. This signal word is limited to the most
extreme situations.
WARNING: Indicates a potentially hazardous situation that, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation that, if not avoided
may result in minor or moderate injury. It may also be used to alert against
unsafe practices that may cause property damage.
2.0 SPECIFICATIONS
MODEL
Part Number
Fuel Type
Power
Tank
Max Cutting Depth
Max Cutting Width
Minimum Clearance from Wall (side)
Minimum Clearance from Wall (front)
Cutting Speed
Arbor
Blade Size
Blade Width
Dust Collector Size
Weight
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
MC-800 JOINT HOG
SX77160WC
Propane
16 HP Vanguard V-Twin Certified Propane/
Electric Start
Vapor - 20 lb
1-3/4" (8" Blade) Fully Adjustable
up to 4"
2.5 feet per minute at 2" wide
1" deep - full mill
1" with Drive Pin Hole
.125 & .150
400+ CFM is recommended
240 lb
2
3"
7"
8"