Advertisement
O
PELONIS"
3 SPEED WALL FAN WITH
REMOTE CONTROL
OPERATING INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
MODEL : WF18RC
CAUTION
Read Rules for Safe operation and Instructions Carefully.
WARNING
1.
Suitable for use with solid-state speed controls.
2.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If plug does not fit fully in the outlet, reverse plug. If it still does not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
3.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
4.
Do not leave the fan running unattended.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These lim¬
its are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radi¬
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
1.
Never insert fingers, pencils, or any other object through the guard when
fan is running.
2.
Disconnect fan when moving from one location to another.
3.
Disconnect fan when removing guard for cleaning.
4.
DO NOT use fan in window. Rain may create electrical hazard.
STEP 1 Unscrew the spinner clockwise and the nut counter clockwise
to remove both of them.
STEP 2 Set the rear guard in the proper position with handle up.
STEP 3 Screw on plastic nut tightly to attach rear guard.
STEP 4 Discard plastic sleeve on shaft.
STEP 5 Install the blade onto the shaft until it reaches the
retaining pin.
STEP 6 Screw spinner onto motor shaft counterclockwise to blade.
STEP 7 Press the rim of the front guard onto the rear guard until the
front guard is properly fitted.
STEP 8 Secure both guards firmly by tightening the fan guard locking
screws and nuts.
STEP 1.2.3
STEP 4.5.6
STEP 7.
INSTALLATION
Spinner
Front grille
-KB
STEP 8.
The fan should be installed on a solid wooden or pillar which
stands vertically to the floor.
Caution: To prevent the fan from falling off, do not install it on
walls less then 10 cm thick or made of materials that are easily
damaged.
Installing the mounting bracket
Fix the supplied mounting bracket firmly to the wall using the three
screws.
NOTE: The bracket should be positioned at least 35cm from the ceiling and
at least 30cm from adjoining wall.
Installing the stand
Mount the stand on the bracket by inserting the bracket catch into
the slot on the stand. Fix the stand onto the bracket with a retaining nut.
NOTE: If the retaining nut does not pass through the holes,
push the stand downwards until it is fully mounted on the bracket.
bracket
Screw
Slot on rear side
Retaining nut
WF18RC/06
(Eng)
ON/OFF KEY
This key is for switching the fan on or off.
SPEED KEY
The fan will start at medium speed.
After 2 seconds it will automatically switch to low speed.
After the fan has started, this key serves as a speed selector in the sequence from
LOW — MEDIUM — HIGH — LOW — MEDIUM when this key being touched
repeatedly or continuously.
ON/SPEED/OFF KEY
This key is for switching the fan on. The fan will start at medium speed.
After 2 seconds it will automatically switch to low speed.
After the fan has started, this key serves as a speed selector in the sequence from
LOW—MEDIUM-HIGH—OFF—LOW-MEDIUM when this key being touched
repeated or continuously. Press this key if the fan needs to switch off.
OSCILLATION CONTROL
Adjust the position of the
oscillation by pulling the pull
switch. (A)
•
Push the guard lightly to
the desired up hr down
direction.
INSERT THE BATTERIES (Not Included)
1.
Press down on the battery compartment cover and slide it out.
2.
Insert the batteries, making sure that the positive terminals are facing
the proper way.
3.
Replace the cover.
NOTE: Use size "AAA" manganese or alkaline batteries. Do not use rechargeable
batteries. (Batteries not included)
iE THE REMOTE CONTROL CORRECTLY
Point the remote control at the receptor on the base of the fan stand and press the
desired button.
The remote control will work at distances of up to roughly 4.5 meters and the
angle of 60 degree included between right and left from the receptor.
The batteries must be removed from the remote control before they are scrapped
and disposed of safely.
OVERHEAT PROTECTION OF THE MOTOR
This fan is equipped with an internal over heat protection device which
causes the unit to stop operating in the event of the motor overheating.
CLEANING
1.
Be sure to unplug from the electrical supply source before cleaning.
2.
Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly
remove soap film with clean water.
3.
To disassemble each part, reverse the order assembly, Securely fasten the grills together.
4.
Be sure not to let water or other liquids enter the inside of motor.
Advertisement
