Related Manuals for Sylvox RT22R2GNDA
Summary of Contents for Sylvox RT22R2GNDA
- Page 1 S l ox 22/24inch RV TV S l ox Model: RT22R2GNDA RT24R2GNDA USER’S MANUAL Note: The product and illustrations in this user's manual is only for explanation purposes and may vary depending on model.
- Page 2 General Information To avoid damaging the television set please observe the following safety instructions during setup and use. Cleaning the television set Before cleaning, disconnect the television set. Use only a soft USER'S MANUAL damp cloth or a special cleaning product for flat-screens. LED Display Too much pressure on the screen can damage the television set.
-
Page 3: Table Of Contents
IMPORTANT - Please read these instructions fully before installing oroperating WARNING: Never let people (including children) with reduced physical, sensory or Content mental capabilities or lack of experience and / or knowledge use electrical devices unsupervised. For ventilation purposes, leave at least 5cm of free space around the TV. The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. -
Page 4: Accessories
Specification Accessories Please make sure the following items are included with your TV. If any items are missing, Please contact us. RT22R2GNDA RT24R2GNDA 22" 24" DC 12V 1920 X 1080 Instructions Manual Warranty Card 2 x 5W Product Dimensions Adapter Power Cord 19.7... -
Page 5: Installation
Installation Overview VOL+ VOL- SOURCE MENU S l ox SPEAKER VOL+/- REMOTE CONTROL SENSOR Press to increase or decrease the volume. Screw POWER INDICATOR In the on-screen menu, use the VOL +/- Screw hole C Green: In power on mode. buttons as left/right arrow buttons. -
Page 6: Remote-Control Unit
Overview Remote-Control unit POWER: Power on/off button, press once to turn the TV on and press again to turn the TV off. MUTE: Press this button to mute or restore sound. 0-9: Select and switch to a channel using 0-9. -/--: Switch the program digit. -
Page 7: General Description
General Description TV Quick Installation Guide 1.Connect an Antenna or Cable to your TV set Installing Batteries in the Remote Control 2.Connect the power cord and turn TV on. Installing Batteries 3. Go to initial Setup. If using the TV for the first time, the initial setup menu will display. Open the battery compartment cover on the back side. -
Page 8: Osd Menu Operations
Picture OSD Menu Operations Press SOURCE button to display the input source list. Press ▼/▲button to select the input source you want to watch. Press ENTER button to enter the input source. Function introduction Item Variablerange Default Explanation Standard / Dynamic Picture Mode Standard /Soft/ User... -
Page 9: Sound
Time Sound Function introduction Function introduction Item Variable range Default Explanation Item Variablerange Default Explanation Standard / Music Sound Mode Standard / Movie / User Off/5Min/10Min/15Min/30Min SleepTimer 0---100 Bass /45M in/60Min/90Min/120Min 0---100 /180Min /240Min Treble Pacific /Alas ka/Hawaii 0---100 Balance Time Zone Pacific Off / On... -
Page 10: Setup
Setup Lock Function introduction Item Variable range Defaul Explanation Note: English / French Now the reare only three kinds of language for Menu Language English Input the correct password with four number(from 0-9), then you can enter next level menu. If the OSD, if clients need more, we can add. - Page 11 Function introduction Item Variable range Explanation Defaul Password to access user-defined menus. Set Password Child lock main switch, if it is off, US and System Lock Off / On Canada will be gray. US V-chip set. Canadian V-chip set. Canada Canadian V-chip set.
-
Page 12: Channel
Channel Note: Before the reset, it should alert the user and then confirm again. Function introduction Item Variable range Explanation Defaul Air/Cable Air/Cable Cable Auto Scan Favorite Show/Hide Among all the Channel No. channels searched Channel Label DTV Signal Cable System User can select the standard mode for the wire search channel. -
Page 13: Fm Menu Operations
Press VOL+ button to Frequency, then press vol+ again to select Frequency value , press FM Menu Operations VOL +/- to fine-tune , press CH+ button to manual scan, Press and hold CH- to exit Frequency selection. Adjust the FM Screen Remarks: TV cable must be plugged into the tv tuner jack before FM scanning&listening. -
Page 14: Dvd
SOURCE Press the “SOURCE” button menu. The up and down direction keys can be selected, or Press the left or right button to select the DVD, and press the Enter button to enter. Press the DVD SETUP button to enter that function. OSD LANGUAGE Set the OSD Language options. -
Page 15: Read Before Using Apps
Read Before Using Apps Troubleshooting (*Terms & Conditions Apply) Due to the product characteristics featured on the Apps store, as well as limitations in available content, certain featured applications, and services may not be available on all devices or in all territories. - Page 16 Symptoms Possible solutions FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two Check your area is covered by Digital Video Broadcasts. After Auto Tuning only conditions: (1) this device may not cause harmful interference, and (2) this device must Try re-tuning or manually tuning missing channels.
-
Page 17: Warranty
Warranty Warranty Period: Thank you for purchasing this Sylvox product. We are glad to offer 12 months free warranty for you. Sylvox repairs the TV free of charge under the condition of the normal use of the instruction If you have any questions, please contact us via our after-sales email or website for assistance.
Need help?
Do you have a question about the RT22R2GNDA and is the answer not in the manual?
Questions and answers
can it be hooked up to a phone to watch tv
The Sylvox RT22R2GNDA has an earphone port for private listening, but there is no information indicating it can be connected to a phone for watching TV. Therefore, it cannot be determined if phone-to-TV video connectivity is supported.
This answer is automatically generated