Download
Share
Print this page
Bofa AD Nano+ User Manual
  1. Manuals
  2. Brands
  3. Bofa Manuals
  4. Scrubber
  5. AD Nano+
  6. User manual

Bofa AD Nano+ User Manual

Hide thumbs

Advertisement

Quick Links

AD Nano+

Advertisement

loading
Need help?

Need help?

Do you have a question about the AD Nano+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bofa AD Nano+

Summary of Contents for Bofa AD Nano+

  • Page 1 AD Nano+...

  • Page 2: Table Of Contents

    Contents Overview 1 01 Overview of your extraction system (front) Overview of your extraction system (back) Overview of the Control Panel Safety Instructions Important safety notes Safety labels Before Installation 3 01 Unpacking and unit placement Installation 4 01 Connecting to power supply Optional Interfacing Operation 5 01...

  • Page 3: Overview 1

    Overview Control Panel Combined Filter Combined Filter Lever Door Latches Pre Filter Lockable Castors...
  • Page 4 Overview Mains Inlet Mains Isolation Switch Exhaust Outlet Signal Cable Inlet (Optional) Air Cooling Air Inlet...
  • Page 5 Overview...

  • Page 6: Safety Instructions

    This does not signify a dangerous or harmful  situation. Refer to manual when this symbol is displayed. Visit our website at www.bofa.co.uk for on-line help.  Or contact the helpline on +44 (0) 1202 699444, Electrical Safety Mon-Fri, 9am-5pm.
  • Page 7 Serial Number Label Safety Instructions Warning and Information labels Location: Next to mains inlet. The following listing details labels used on your AD Nano+ Meaning: This label contains a variety of information about unit. the extraction unit, including: Goggles, Gloves & Mask Label ...

  • Page 8: Before Installation 3

    Before installation 3. With the unit in position lock the 2 front castors. Inner transit packaging removal & unit placement Before installation, check the extraction unit for damage. All packaging must be removed before the unit is connected to the power supply. Caution Please read all instructions in this manual before using Do not block or cover the cooling vents on the unit, as this...

  • Page 9: Installation 4

    The supply cord should only be replaced by a BOFA engineer as an electrical safety test may be required after replacement. The AD Nano+ MUST be connected to a properly earthed outlet.
  • Page 10 Override Installation Enables the extractor to operate fully with or without either DC voltage input or the Volt free input. The override feature can be toggled On / Off by a switch mounted on the internal motor access panel (see below for switch location) Switch in “On”...

  • Page 11: Operation 5

    To set the airflow Operation Hold down the Up and Down arrows on the front panel for 5 seconds. The green LED will now start to flash, indicating that the machine is now in set mode. You can now increase or decrease the flow by holding down either the up or down arrow.

  • Page 12: Maintenance 6

    Filter Information Maintenance A log of filter changes should be maintained by the user. The filters require attention when the display shows the configuration shown on the next page or when the extractor no longer removes fume efficiently. It is recommended that a spare set of filters are kept on site Maintenance UK to avoid prolonged unit unavailability.
  • Page 13 Maintenance To remove and replace the combined filter follow the procedure detailed below. Isolate the electrical supply to the extractor 2. Open the door of the unit. Remove the upper (combined) filter. 4. Fit new filter. Filter Replacement Close the door and fasten the latches. During use, the AD Nano+ will alert the user when its filter 6.

  • Page 14: Replacement Parts

    To maintain performance it is important that the filters are associated risks defined. replaced with identical BOFA filters. To re-order please refer The thresholds for these to the Filter number printed on the filter installed in your risks can then be compared extraction unit.

  • Page 15: System Specifications

    System Specifications Unit: AD Nano Capacity: 300m Weight: Motor: Centrifugal Fan Output: 1100ω Electrical supply: 100-240V Hertz: 50/60Hz Full Load Current: 230V: 10.0A Noise Level: Below 60dB (A) (at typical operating speed) Size: Metric Imperial (mm) (inches) Height 31.4 Depth 17.2 Width 14.9...
  • Page 16 Contact Information BOFA Headquarters 21-22 Balena Close Creekmoor industrial Estate Poole Dorset BH17 7DX Phone: +44 (0) 1202 699444 BOFA Americas 303 S.Madison Street Staunton Illnois 62088 Phone: 001 (618) 205-5007...