Download Print this page

Advertisement

Quick Links

FLYWAY
30

Advertisement

loading
Need help?

Need help?

Do you have a question about the FLYWAY 30 and is the answer not in the manual?

Questions and answers

Summary of Contents for DoAll FLYWAY 30

  • Page 1 FLYWAY...
  • Page 2: Included Parts

    INCLUDED PARTS (2) Safety Ring Arms and (4) Main Spring and Trap Head (4) Stacker Poles M6X7 Allen Screws Spade Bolt with Hand Crank (2) M8X10 Studs Rear Base Stand (2) Front Leg Brackets Horseshoe and (4) Safety Ring (4) Set Screws for legs and base 1/4"...
  • Page 3 STEP 1 Begin by flipping the Trap Head upside down. First, thread in the studs for the safety ring, which thread, by hand, from the outside in on each side of the rear of the trap, as shown above.
  • Page 4 STEP 2 While the trap is still upside down, install the Front Leg Brackets and Safety Ring Arms (pointing forward, in the direction that the arm will throw the clays) using the (4) provided allen head screws. Secure the bolts with a 6mm alen wrench.
  • Page 5 STEP 3 Next, slide each of the Front Legs onto their brackets, choosing which height to fasten them at. Secure these with (2) of the provided Set Screws.
  • Page 6 STEP 4 Next, slide the Rear Base Stand on the rear of the trap, as pictured above. Secure these with the remaining (2) of the provided Set Screws.
  • Page 7 STEP 5 Now, rotate the throwing arm out to the 12 o’clock position as depicted above. Hook Main Spring onto the eyelet towards the front of the Trap Head. Remove the Hand Crank and slide the Spade Bolt through the hole in the rear of the trap.
  • Page 8 STEP 6 With the trap now flipped back to the upright position, Slide the Safety Ring through the Safety Ring arms and connect to each of the M8X10 Studs towards the rear of the Trap.
  • Page 9 STEP 7 Remove the (4) rubber caps on top of the Trap Head, then slide each of the Stacker Poles onto the now exposed mounts. Then, secure the Horseshoe to the top of the Stacker Poles using the (4) provided bolts and an 11MM socket, with the opening facing the rear of the trap.
  • Page 10 THANK YOU ONCE THE MAIN SPRING IS INSTALLED, THE TRAP IS NOW LIVE AND CAN GO OFF IF LEFT IN THE COCKED POSITION. PLEASE USE EXTREME CAUTION AND ALWAYS REMOVE SPRING WHEN TRANSPORTING, ADJUSTING, OR STORING THE TRAP.
  • Page 11: Operation

    Operation 1. Make sure deep cycle battery (not included) is fully charged. Before clamping trap alligator clips to battery, make sure the toggle switch on the trap is set to off. **NEVER CARRY TRAP BY THROWING ARM - THIS CAN BEND AND AFFECT PERFORMANCE! 2.
  • Page 12: Troubleshooting

    Troubleshooting ***ALWAYS REMOVE MAIN SPRING PRIOR TO TROUBLESHOOTING*** MACHINE NOT TURNING ON 1. CHECK BATTERY CONNECTION. THE MACHINE DRAWS 16 AMPS TO WORK PROPERLY. WE RECOMMEND A DEEP CYCLE BATTERY WITH A MINIMUM OF 675 COLD CRANKING AMPS. 2. CHECK THE 15A AUTOMOTIVE BLADE FUSE IN THE REAR OF THE TRAP HEAD. REMOVE THE COVER AND PULL THE FUSE OUT TO INSPECT.
  • Page 13: Warranty And Customer Service

    OTHER 1. IF THE CLAY IS FLYING WITH A WOBBLE, THE THROWING ARM IS BENT AND WILL NEED TO BE BENT BACK OR REPLACED. NEVER CARRY THE TRAP BY THE ARM. 2. IF THE MAIN GEAR AND MOTOR ARE MOVING BUT THE THROWING ARM ISN'T THEN THERE MAY BE AN ISSUE WITH THE CLUTCH ASSEMBLY.