Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ASC Gruvlok 3006
Summary of Contents for ASC Gruvlok 3006
- Page 1 Gruvlok Roll Groover ® 3006 & 3006C Manual...
- Page 2 - pipe to pipe and people to people. We've always been dedicated to building connections that last. As ASC Engineered Solutions, we are ready to make those connections stronger than ever by focusing as much on how we serve our customers as on the products we provide.
-
Page 3: Table Of Contents
Troubleshooting 17 Important Safety Notice Carefully read and understand instructions before assembling and operating the Groover(s). Become thoroughly familiar with the Groover operation, usage and possible hazards specific to the Groover(s). Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... -
Page 4: Safety Instructions
Ridgid 300 support arms and the Groover driveshaft firmly tight ened into the Ridgid 300 chuck jaws. 8. Unplug the Ridgid 300 Power Drive power cord prior to servicing or changing groover parts. Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... -
Page 5: Groover Description
Copper: 2"- 2½" - Type M, 3"- 8" - Type DWV 3. Please contact an ASC Engineered Solutions Representative for information on grooving alternate materials and wall thickness. D. Grooving Times This chart shows approximate grooving times with the groover set-up for the proper size and groove diameter and the pipe properly positioned on the groover. -
Page 6: Installing Support Leg Assembly
Groover back into the chuck jaws. just slightly to permit pump to Securely tighten the chuck jaws. be oriented by operator to most comfortable position during Groover operation. Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... -
Page 7: Pipe Set-Up And Positioning
Turn the nut counterclockwise sufficiently to allow clearance between the bottom of nut and top of housing when the top grooving roll is in contact with the pipe. Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... -
Page 8: Setting Groove Diameter
²/ ²/ ₃ ₃ ²/ ²/ ₃ ₃ ²/ ²/ ₃ ₃ ⁵/ ⁵/ ₆ ₆ ½ ½ ½ ½ ½ ½ ½ ½ Portion of Turn Portion of Turn Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... -
Page 9: Grooving Ips Steel Pipe
Groover and roll a new groove. Recheck 10" .188" 4,600-5,000 the groove diameter for conformance to grooving specifications 12" .219" 4,600-5,000 2" 2,800-3,200 2½"- 4" 40, 40S 4,200-4,600 5"- 8" 4,600-5,000 5"-6" 4,600-5,000 Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... -
Page 10: Grooving Cts Copper System
Continue to raise the pressure until a groove starts being 5" 1,800 1,400 1,100 formed. Use the following table as a guide for grooving pressures. 6" 1,500 1,100 8" 2,000 2,400 1,500 1,100 Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... -
Page 11: Grooving Roll Change
Lower the top roll from between the front and back plates of the grooving head. Remove thumb screw from top shaft and return to storage location. Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... - Page 12 This will align the V-groove the front of the Groover. with the locator setscrew in the groover head. Care should be taken to avoid contacting the plain diameter of the shaft. Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®...
-
Page 13: Groover Maintenance
Frequency of lubrication should be increased in harsh environments. A. Grease Fittings B. Replacement Parts Please contact your ASC Engineered Solutions Representative to purchase Apply grease to front replacement parts for the Roll Groover. To ease ordering, an exploded... - Page 14 Support Leg Assembly GL11374 11 Dowel Pin GL11290 2F Flat Head Screw, ¼-20, L=¾" GL11108 12 Cone Pt. Set Screw, 5⁄ ₁₆ -18 GL11066 2G Cap Screw, ¼-20,L= ½" GL11230 Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®...
-
Page 15: Groove Specifications
ID prior to roll grooving. Failure to do so may Notes: result in damage to the roll grooving machine and VdS - Roll Grooving Approval Specifications, see the Technical Data/Install Instructions section on ASC Engineered Solutions' web unacceptable roll grooves may be produced. site - www.asc-es.com “A”... - Page 16 202.16 -0.51 208.8 COLUMN 7 - DWV (Drain, Waste and Vent Piping) per ASTM B306. COLUMN 8 - Maximum flare diameter is the OD at the most extreme tubing diameter. Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®...
-
Page 17: Troubleshooting
Hand pump is low on oil. See "Groover Maintenance" Air in hydraulic system. See "Groover Maintenance" Tool won't groove pipe. Pipe wall thickness exceeds See "Groover Description" tool's capability. Gruvlok Roll Groover 3006 & 3006C Manual | asc-es.com ®... - Page 18 ® ® With headquarters in Oak Brook, IL, ASC also has ISO 9001:2015 certified production With headquarters in Oak Brook, IL, ASC also has ISO 9001:2015 certified production With headquarters in Oak Brook, IL, ASC also has ISO 9001:2015 certified production With headquarters in Oak Brook, IL, ASC also has ISO 9001:2015 certified production facilities in PA, TN, IL, TX, AL, LA, KS, and RI.
Need help?
Do you have a question about the Gruvlok 3006 and is the answer not in the manual?
Questions and answers