Table of Contents
Advertisement
Settings for DVD Operation (continued)
Audio Output
Select the digital output to be output from the optical
digital audio output connector of DECK.
1 Do steps 1 and 2 on p. 45.
DVD MAIN MENU
Press AV*
QUA iaa
| tO select
|
Ty MODE on:
: 3 | "AUDIO OUTPUT,"
and
SELECT
iay
press
SET
to display screen.
Press AV
to select an item, and
press SET
repeatedly for output.
END
¿ACTION
E "LPCM (DVD)" selections
OFF: Linear PCM of less than 48 kHz/16 bit is
output. When playing DVDs recorded in
linear PCM of over 48 kHz/20 bit or 96 kHz,
no digital audio is output. (Factory preset)
When playing DVDs recorded in linear PCM
of 48 kH2/20 bit/24 bit or 96 kHz, digital
audio converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright
protection.)
"Dolby Digital" selections
Bitstream: Dolby Digital bitstream (1ch-5.1ch)
is output. (Factory preset)
OFF:
No output.
E "dts" selections
Bitstream:
dts bitstream is output. (Factory preset)
OFF:
No output.
@"DRC(Dynamic
Range Compression} selections
OFF: Normal audio range is selected. (Factory
preset)
For dynamic sound even at low volume, this
is useful for late-night listening. [Dolby Digital
DVDs only].
@ "SURROUND" selections
Surround Sound creates the effect of sound coming from
non-existent rear speakers even when only connected toa
2-channel stereo system.
OFF:
No Surround Sound effect. (Factory preset)
ON:
Surround Sound effect.
PCM:
ON:
Press ACTION to redisplay DVD menu
and go to step 2 to setup another item.
Or, press ACTION three times to exit.
46
Recommended
setting
LPCM | Dolby
(DVD) | Digital
OFF
OFF
AV amplifies (with digital
PcM''|
OFF'? | OFF?
audio input connectar)
without Dolby Digital/dts
,
J
decoder
AV amplifier including
Dolby Digital decoder
AV amplifier including
Dolby DigitaVdts decoder
* Make settings according to amplifier
connected to optical audio output as shown
in above table.
* When a dts decoder is not connected, to
enjoy dts DVD, please select audio output
other than dts at the dts DVD menu screen.
Otherwise, there will be no sound.
Type of amplifier
to be connected
*4 Audio Output 2 from DECK is converted to
48 kHz/16 bit in addition to audio from digital
audio output.
To enjoy high quality sound at 48 kHz/20 bit
124 bit or 96 kHz, connect the amplifier or
decoder directly to the Audio Output 2
connectors, not to the Digital Audio Output
connector. [Select"OFF"atthe"LPCM(DVD)"]
*2 When connecting an amplifier (with an
optical digital input connector) which does
not contain the Dolby Digital or dis decoder,
be sure to select "OFF".
If "Bitstream" is selected, starting DVD play
may cause such a high level of noise as to
be harmful to your ears and damage the
speakers.
*3 When a dts decoder is connected, please
select "Bitstream" in "dts". If "OFF" is
selected, there will be no sound.
* Turn off other surround effects when using
this surround effect.
* For optimum effect, the distance between
DECK and the listener should be about 3 or 4
times the distance between the right and left
front speakers.
For assistance, please cal! ; 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Advertisement
Table of Contents
