jablotron JA-162PC Quick Start Manual

JA-162PC, JA-162PC-GR, JA-162PC-AN Wireless PIR motion detector with
Type: 5PIRCAM2202MQ
This device is a wireless component of the JABLOTRON system. It serves
for the detection of human movement in building interiors and visual alarm
confirmation. The camera takes colour photos with a resolution of up to
640x480 pixels. The camera is equipped with a visible flash for taking photos
in the dark. The images are saved in the internal memory of the detector and
then they are forwarded to the control panel and from the control panel they
can be sent to MyJABLOTRON or ARC. The detector can also take a photo by
request.
The detector takes one position in the system and should be installed by
a trained technician with a valid certificate issued by an authorized distributor.
The product is compatible with the control panels JA-102K,
JA-103K, JA-107K or above.
The photo-verification can be used only after
the registration of the system to MyJABLOTRON or
with subsequent ARC service.
Installation
T
he detector can be installed on the wall or in the corner of a room. There
should be no objects which quickly change temperature (e.g. heating
appliances) or which move (e.g. curtains hanging above a radiator, robotic
vacuum cleaners, pets) in the detector's field of sight. It is not recommended
installing the detector opposite windows or in places with intense air circulation
(close to ventilators, heat sources, air conditioning outlets, unsealed doors,
etc.). There should be no obstacles in front of the detector which might obstruct
its view of the protected area.
Fig: 1 – Camera flash; 2 – Camera lens; 3 – LED indicator; 4 – PIR detector
lens; 5 – locking screw; 6 – cover tab;
1. Open the detector cover (by pushing the cover tab (6). Avoid touching the
PIR sensor inside (13) – you could damage it.
2. Camera is fixed to the plastic base by right locking screw. Remove the
right locking screw (8) and release the PCB by a tab (14).
3. The recommended installation height is 2.5 m above the floor.
4. Attach the plastic base to the wall using screws (vertically, with the cover
tab facing downwards).
5. Re-insert the PCB and secure it with the tab (14) and supplied locking
screw (8).
Fig 2: 7 – battery holder; 8 – camera module locking screw; 9 – LED
indicators; 10 – external tamper connector; 11 – serial number; 12 – tamper
switch; 13 – PIR sensor; 14 – PCB tab
6. Proceed according to the control panel installation manual.
Basic procedure:
a. The control panel must contain already enrolled JA-11xR radio
module.
b. Go to the F-Link software, select the required position in the Devices
tab and launch the enrollment mode by clicking on the Enroll option.
c. Insert the batteries (mind the correct polarity). When the second
battery has been inserted into the detector, an enrollment signal is
transmitted to the control panel and the detector is enrolled to the
JA-162PC, JA-162PC-GR, JA-162PC-AN
a 90° verification camera
d.
7.
Close the detector cover and test its functionality.
Notes:
−
−
−
−
−
Settings can be set by F-Link software in the Devices tab. Use the Internal
settings option on the detector's position to open a dialog window where you
can configure the settings (* default settings):
PIR immunity level: Defines false alarm immunity. The *Standard level
combines basic immunity with a rapid reaction. The Increased level provides
higher immunity but the detector reaction is slower.
Taking photos during alarm: No flash, *With flash
Flash intensity: Low, *Medium, High – if the captured scene is over-
exposed (e.g.in a small room), the intensity of the flash can be decreased.
It can be increased for larger spaces, but utilizing this option reduces battery
lifetime.
LQ photo quality: *Standard quality uses optimized compression in order
to achieve the fastest possible transfer to the ARC or to the end user
in MyJABLOTRON. The goal is achieving alarm verification in the fastest time
possible. If the quality is switched to Extended, the system will use lower image
compression which will at least double the time necessary to transfer the image
(depends on the conditions of the captured scene). Change the quality only if
the LQ image does not have the quality required by the customer – it may
depend on the captured space. It is not recommended when there are more
verification detectors in the premises which may take images at the same time.
Send pre-alarm photos: *With flash, No flash. When this parameter is
enabled, the detector will send photos even when the detector is configured
with repeated or confirmed reaction and the alarm has not been confirmed.
During every entrance delay, up to 2 photos can be taken when the detector is
triggered even when the system has been unset properly.
This option will noticeably increase the volume of data transferred
to MyJABLOTRON. If the system is not unset (alarm is triggered), the images
taken during the entrance delay will be sent automatically regardless of this
option.
PG output reaction: You can select PG outputs, whose activation will
trigger taking a picture (* No, camera does not react to PG). For further info
see Installation recommendations, cautions.
Taking a photo by PG activation: *No flash, With flash.
Increased number of photos during alarm: When enabled, 3 photos are
sent instead of 2 during each alarm event, that means more data transfer
between the detector and the control panel and between the control panel and
MyJABLOTRON or ARC. This option is for specific markets, so we don't
recommend enabling by default. Utilizing this option reduces battery lifetime.
Sensor of tearing-off form the wall: Enables the option to utilize an
external tamper connector if the JA-191PL joint bracket.
Take a photo: takes a test photo (LQ) with a flash and F-Link displays it.
When the Detail button is pressed, the F-Link software shows the picture in
a 640x480 px resolution. Photos are sent to MyJABLOTRON (provided that
transferring is enabled).
The process of how the camera takes pictures depends on the settings in
the F-Link software – the Devices tab. Choose a type of Reaction on the
detector's position.
Instant: During an alarm triggered by the detector, the camera can be activated
up to 3 times (then it will be auto-bypassed). Each activation, depending on the
detected movement and settings, takes 3 photos maximum. Photos are sent to
the control panel (9 photos maximum).
Delayed: The first activation (entrance delay) takes up to 2 photos according
to the detected movement and saves them into the internal memory (Send pre-
alarm image disabled). When alarm is triggered, photos are sent from the
selected position. If a battery with not enough charge is inserted into
the device, the LED indicator will flash yellow for five minutes at a 2Hz
frequency.
If the detector is enrolled as the first PIR camera or the control panel
is not connected to MyJABLOTRON, F-Link shows a dialogue window
with the question about enabling data transfer. We recommend
enabling this option with the agreement of the customer and
confirming this acceptance by recording it in the system service log
with his signature.
Note: If the transmission is not enabled, images will be saved in the
internal memory of the detector and the control panel only. Then it is
impossible to send them to MyJABLOTRON or ARC.
When the control panel is in service mode, the detector indicates every
movement with the red LED indicator.
If you want to enroll the detector in the control panel after the battery
has already been inserted, remove the battery first and then press and
release the tamper contact (12) to discharge the rest of the energy and
then enroll the detector.
The detector can be enrolled by entering the production code (11) in
the F-Link software (or a bar code reader). Enter all digits located
below the bar code (1400-00-0000-0001).
If you want to remove the detector from the system, erase it from its
position in the control panel.
In order to comply with the EN 50131-2-4 norm, the cover tab (6) must
be secured with the supplied screw (5).
Detector internal settings
Camera and basic reactions:
1 / 2 MMQ56604