Advertisement
HOW TO USE AS A STEAM IRON fs we
pe
sary Use a press cioth on top of fabric.
@ Remove the Cover Case: Place the unit on a firm and stable surface, while press
the Case Lock Button, lift the Cover Case to open.
He
i
=
@ Romove the Tank
=
©
a) Move the Steam/Dry Selector to Dry ( 关 ) position,
b) Press the Water Tank Release Button; take out the
Water Tank,
(3) a) Open the Water Fill Cover.
b) Fill the Water Tank up to " 满 水 (MAX) "line.
Notice: (1) Observe the volume of water at upright
position, do not overfill above " 满 水 (MAX)"
indication,
@ Using pure tap water.
® While fill Water Tank with water, don't plug
the AC Power Cord into electrical outlet.
a) Close the Water Fill Cover.
b) Re-install the Water Tank to the main unit, untill
a click sound is heard.
©
Hold the plug and pull the Power Cord out to suitable
Length, then Plug the AC Power Cord into electrical
outlet, connect to power supply.
Set the iron on the Power Base securely.
Push the Temperature Selected Button until the
red light for steam zone starts blinking.
©
selected temperature. Just put the iron into Power Base,
don't put it at other place.
* This iron must be used with its Power Base.
® After take out the iron from Power Base, you can iron continuously
for about 90 seconds to 120 seconds. (use for steam iron and set
temperature to "高 ")
* Different time for different condition.
Steam/Dry Selector (switch as the following)
Light
steam; for thin or delicate fabrics
requiring a small amount of
steam.
Regular steam: for fabrics requiring a lot of
steam (i.e.thick materials,
items with stubborn wrinkles.)
i
Can use vertically
Dry( 关 ) Lightsteam
Regular steam
@ How to use the Jet of Steam feature
a) For fabrics of thick materials and with stubborn wrinkles,
and cleaning the steam vents at the same time.
b) Pump the Jet of Steam Button several times before
using for the first at each ironing session.
c) The interval should not less than 2-5 seconds
when using the Jet of Steam, to avoid the hot
water dripped from the Soleplate.
d) When using Vertical Steam, hang the garment on
a clothes hanger. Hold the iron away from your
body close to but not touching the fabric,
Pull the fabric tight with your free hand and after
2-5 seconds press the Jet of Steam Button.
Notice:
(D When using Jet of Steam, keep the Steam/Dry
Selector in the Dry( 关 ) position and set the
Temperature Selected Button to "高 " zone, or
Shake the
water tank
Notice: © Do not leave the iron unattended while
村
some water will drop from iron.
《
itis connected to the electrical source.
steam
Br lc eenparatine
2) Never iron clothes on the body or point your iron
2) When use Regular Steam or Jet of
San
loons
at anyone when steaming
afl
Steam, please set the Temperature
owal
The water volume can be observed very clearly whatever in
j )
Selected Button to "高 " zone. Low
5
vertical or horizontal position. Please pull out the Plug when
HP
temperature will lead to water leakage.
E
the volume of water is low, and refill the iron according
VE
@ a Preheat the iron until the indicator Light change from blink
tothe step @-@
Selector to tho ont)
to illumination( while the iron being use, it reheat itself when
a) After ironing, push the Temperature Selected Button until
as
the temperature decline, the light doesn't blink.)
the " OFF( 断 开 ) " light turns on, pullout Plug.
mp
b) Move the Steam/Dry Selector, select steam quantity; and start to iron.
b) Move the Steam/Dry Selector to the "Dry()" position,
Notice: (1) The iron should be set on the Power Base
press the Water Tank Release Button, take out the Water Tank.
securely for connecting to power supply,
c) Empty water from Water Tank.
While not in use, please set back to Power
d) Re-install Water Tank, keep the Steam/Dry Selector in the
Base, the Power Base will maintain the
A
AOR
postion.
p
-18-
-14-
Advertisement
