Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for RFDesign RFD X Series
Summary of Contents for RFDesign RFD X Series
- Page 1 RFD X-Series Enclosure Mounting Instructions...
-
Page 2: Table Of Contents
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au Contents Overview ............................2 Components ..........................3 Diagram ........................... 3 Assembly ............................4 Additional Items ........................4 Steps ............................5 Cable Restraint ........................6 Mounting ............................7 Considerations ........................7 Configurations ......................... 7 Configuration A: Tabs ........................7 Configuration B: Zip Tie ........................ -
Page 3: Overview
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au 1 Overview This black ABS injection moulded case is purpose built for an RFD900x or RFD868x modem, intended for use of both professionals and hobbyists alike. Built as the solution to address ease of mounting, protection, and security for the modem inside and connecting cables. -
Page 4: Components
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au Components Enclosure lid • Enclosure base • Light pipe • 2x M2.5 5mm screws • 3x M2.5 14mm screws • Hex key • 2mm cable tie (for cable restraint) • Compliance sticker (required in USA and Canada only) •... -
Page 5: Assembly
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au 2 Assembly Additional Items Items that may be required for assembly (not provided): Up to 4.5mm wide cable ties (for mounting) Up to M3 screws (for mounting) RFD900x/868x Modem Cable... -
Page 6: Steps
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au Steps 1. Decide on which mounting method to use (see section 3.2) 2. Find the base of the enclosure (if using mounting configurations C and D go to section 3.2C 3.2D and follow mounting instructions) 3. -
Page 7: Cable Restraint
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au Cable Restraint Use a small zip tie (provided) to secure the cable in place before mounting the enclosure. 1. From the inside of the base, thread one end of the zip tie through one of the slots and up through the other side. -
Page 8: Mounting
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au 3 Mounting Considerations Consider a location which allows cabling to be kept short, and away from • electrical noise sources. Be aware of anything pulling on the cable, consider securing cable with a zip tie •... -
Page 9: Configuration B: Zip Tie
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au Configuration B: Zip Tie 1. Secure to desired location by placing two zip ties (up to 4.5mm wide) into the slots at the top and bottom end of the enclosure and tighten. Configuration C: Inside case 1. -
Page 10: Configuration D: Custom Mounting Bracket
RFD900x/868x Enclosure Mounting Instructions www.rfdesign.com.au Configuration D: Custom Mounting Bracket 1. Mount the base of the enclosure onto an external mounting board using M2 – 2.2 self-tapping screws (not provided) through the mounting holes at the back of the base (see diagram in 3.2 C... -
Page 11: Labelling - Usa And Canada
Please attach the appropriate label for use in USA or Cananda onto the outside of the modem enclosure and ensure it is visible for compliance purposes. Technical support: support@rfdesign.com.au Email: info@rfdesign.com.au RFDesign Pty Ltd Unit 7, 1 Stockwell Place Archerfield QLD 4108 Brisbane, Australia...
Need help?
Do you have a question about the RFD X Series and is the answer not in the manual?
Questions and answers