Related Manuals for RVS RVS-360-MO
Summary of Contents for RVS RVS-360-MO
- Page 1 HD 360° Surround View System With Built-in ECU RVS-360-MO Instruction Manual © Rear View Safety 2023...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction ....................3 In The Box ......................3 Safety Information ..................4 Precautions ....................5 Maintenance ....................8 2. Connection Diagram ................9 3. Technical Specifications ...............10 4. Operation Instruction ................11 4.1 Remote Controller .................11 4.2 User Interface ..................12 Warranty ......................30 Disclaimer ....................31 Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233 800.764.1028 sales@rearviewsafety.com www.rearviewsafety.com... -
Page 3: Introduction
INTRODUCTION Congratulations on purchasing an inView HD 360° Surround View System with built-in ECU and 5-minute calibration! With this manual you will be able to properly install and operate the unit. The system should not be used as a substitute for the standard rear view mirror or for any other mirror that exists in your vehicle. -
Page 4: Safety Information
SAFETY INFORMATION PLEASE READ THE ENTIRE MANUAL AND FOLLOW THE INSTRUCTIONS AND WARNINGS CAREFULLY. FAILURE TO DO SO CAN CAUSE SERIOUS DAMAGE AND/OR INJURY, INCLUDING LOSS OF LIFE. BE SURE TO OBEY ALL APPLICABLE LOCAL TRAFFIC AND MOTOR VEHICLE REGULATIONS AS IT PERTAINS TO THIS PRODUCT. -
Page 5: Precautions
While installing the RVS System be careful with the wire positioning in • order to avoid wire damage. The RVS System should only be used when the vehicle is in reverse. • Do not watch movies or operate the monitor while driving; as it may cause •... - Page 6 If you have questions about this product, please contact us at: 800.764.1028 sales@rearviewsafety.com www.rearviewsafety.com New York 1797 Atlantic Ave Brooklyn, NY 11233 Indiana 319 Roske Dr. Elkhart, Indiana 46516 Canada 68 Trafalgar Square Thornhill, ON, L4J 7M5, Canada IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
- Page 7 PRECAUTIONS Storage and Keeping Do not expose the System to excessive heat or cold. The storage temperature of this device is -30~+80°C, and the operating temperature is -20~+70°C. The humidity is RH90%. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar places.
-
Page 8: Maintenance
MAINTENANCE 1. Remove all the cable connections from the control box before cleaning the device. 2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth. 3. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device. -
Page 9: Connection Diagram
2. CONNECTION DIAGRAM 1. White 4P male - Left Camera and trigger 2. Blue 4P male - Right Camera and trigger 3. Green 4P male - Front Camera, Trigger is Full Screen 4. Brown 4P male - Rear Camera and Trigger (Grid Lines) 5. -
Page 10: Technical Specifications
3. TECHNICAL SPECIFICATIONS Monitor Input video Max.4CH×720P@25/720P@30 Display style 2D and 3D 720P High definition output Refresh Rate 50/60 Working Voltage 8-32V Working voltage range for external 8-32V trigger signals Working electric current <2A/12V -20°C-70°C Working temperature range Storage Temperature -40°C ~85°C Working Humidity 10%-95%... -
Page 11: Operation Instruction
4. OPERATION INSTRUCTION 4.1 REMOTE CONTROLLER ENTER: Enter main menu or confirm menu • selection. ESC: Exit main menu interface/return to main • menu interface. LEFT, RIGHT: Left,Right /Minus, Plus button. • Shift image channel to left/right view, or operate plus/minus in main menu interface. UP, DOWN: Front/Back button. -
Page 12: User Interface
4.2 USER INTERFACE 4.2.1. Log in Interface Password (factory default is 88888888) confirm to log in reset password exit 5.2.2. Password reset current password new password confirm password save setting Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233 800.764.1028 sales@rearviewsafety.com www.rearviewsafety.com... - Page 13 4.2.3. User main interface User Setup: user settings, to set up: Basic Setup, Display, Trigger, ADAS Setup (N/A), Radar, Screen Setup. Storage: storage management, can check the SD storage and log file management (Currently there is no video recording function, this interface is only used for customers to format the SD card through USB) AVM: Calibration File, Vehicle Type, Surround View and Outrigger Information: Software version information and upgrading...
- Page 14 4.2.3.1 User Setup Interface Description: All user setting functions Basic Setup: Basic settings Display: Display mode settings Trigger: Trigger line setting interface Adas Setup: Intelligence assistance setting (N/A) Radar: Radar setting interface Screen Setup: Screen setting Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233 800.764.1028 sales@rearviewsafety.com www.rearviewsafety.com...
- Page 15 1) Basic Setup: basic settings interface, as shown below Display Icon: hide display icons on main interface except direction arrows). Language: Temporarily only English is available. Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233 800.764.1028 sales@rearviewsafety.com www.rearviewsafety.com...
- Page 16 2) Display: select display mode, as shown below Blending Region: blending overlapping ON/OFF. Instant Rear View: Toggle On/Off, the default is ON. When set to OFF, the boot mode is to display the boot logo and then display the panorama screen. When it is set to ON, the single view will appear after booting for 3 seconds, and then the panoramic image will be displayed, requiring the back single view to be a mirror image.
- Page 17 3) Trigger: The trigger line setting interface Trigger Priority: Trigger priority, default value is None. When set to None: Panorama will display the first triggered view. For example, when the rear line (Brown line) is triggered, the rear view camera is displayed in a panoramic view. At this time, if the left road (White line) is also triggered, the back road camera is still displayed in the panorama.
- Page 18 NOTE: The trigger delay is 3s. When a trigger is disconnected, wait for 3s before returning to the default interface. 4) ADAS Setup: ADAS assistance Setup (N/A) Detect Switch: On and Off setup 5) Radar setup interface (Radar/Sensors sold separately) Exit button Enter radar sensor setup interface...
- Page 19 Trigger Control: Trigger control setting, the default is ON. When it is set to ON, the sensor will respond when back line is been triggered; When the trigger control is off, the radar response is not controlled by the trigger line. Speed Control: Speed control setting, the default is OFF.
- Page 20 6) Screen Setup: screen parameters setup Volume: set screen volume (Notice: not available now). Dimmer setup: set screen brightness, user can select Low, Mid (Middle) , High and Auto. When set to Auto, monitor will turn on auto back-light function, which is, screen will turn bright in bright environments (Day mode) and turn dark in dim circumstances (Night mode).
- Page 21 Management Logs: log files list ALL: select all log files None: select none log files Delete: delete the selected log files Export: export the selected log files 5.2.3.3 AVM Interface Automatic Calibration: Automatic Calibration Calibration File: calibration images export and calibration results import Vehicle Type: Vehicle Type replacement Surround View: blending angle and surround view parameter setting Outrigger: Outrigger parameter setting...
- Page 22 4.2.3.3.1 Automatic Calibration Cancel: Cancel button, click this to exit calibration interface. Calibrate: Automatic calibration button, click to enter automatically calibration mode. Calibrate Log: Display of calibration log. Precautions: 1. Each camera should fully see the 2 nearby calibration mats and cannot be blocked by objects. 2.
- Page 23 Vehicle Type: Used to modify the type of car model (note that the car model here is only for auxiliary calibration reference and does not need to be saved) Precision: Accuracy adjustment of vehicle length, width and model movement,default value is 1. (optional values 1, 5, 10, 15 pixels). Vehicle Length: Used for vehicle length adjustment.
- Page 24 4.2.3.3.2 Calibration File Setup: calibration images export and calibration results import Note: this interface does not refresh USB resources in real time, user must first connect USB before entering this interface. Export: export calibration images to USB Drive, including 6channel camera images and XML file Import: import the calibrated result to ECU.
- Page 25 Truck, Fire Truck, Garbage Truck, School Bus, truck, Utility Truck, Van, Transit Bus. Can put the customized vehicle type: copy vehicle type in PNG format to USB drive, and set it in ECU to be the correct vehicle type 4.2.3.3.4 Surround View Setup: Blending angle and surround view parameters setting Blending angle setting: Blending angle of 4 corners can be set separately, range is 0 to 90°...
- Page 26 Unit can be inch/cm ON/OFF: Outrigger ON/OFF. ON display, OFF hidden. Length setting: Outrigger length setting (when Unit is inch range is 0-111 inch, when unit is cm, range is 0-284cm) Width setting: Outrigger width setting (when Unit is inch range is 0-37inch when unit is cm, range is 0-95cm) Position-Y%: Set the display percentage based on vehicle size adjust the location of Outrigger.
- Page 27 4.2.3.4 Information Current Version: current software version. Upgrade Configure: configuration file upgrade. Upgrade: Version upgrade, select the version that needs to be upgraded and click button. System Setup: Reset: Reset to default setting. Import: Import the configuration file. Export: Export the configuration file (currently the configuration file does not include AVM configuration parameters).
-
Page 28: Warranty
ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. -
Page 29: Disclaimer
DISCLAIMER REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS. - Page 30 Engineered For Vehicle Safety™ If you have questions about this product, please contact us at: 800.764.1028 sales@rearviewsafety.com www.rearviewsafety.com New York 1797 Atlantic Ave Brooklyn, NY 11233 Indiana 319 Roske Dr. Elkhart, Indiana 46516 Canada 68 Trafalgar Square Thornhill, ON, L4J 7M5, Canada...
Need help?
Do you have a question about the RVS-360-MO and is the answer not in the manual?
Questions and answers
How to log in without remote
To log in to the RVS RVS-360-MO, use the default password "88888888" on the log-in interface. There is no mention of a remote being required for logging in.
This answer is automatically generated