WAGAN Tech 7316 - AC/DC DIGITAL TIRE INFLATOR Manual

FEATURES

• Automatic shutoff
• Easy-locking air nozzle
• Storage for power cord and air hose
• Adapter tips for balls and inflatables

OPERATION

1. Make sure the power switch is in the "Off" position before plugging in.
2. To achieve optimal performance, when powered by the 12V socket, your vehicle's engine should be running while operating your tire inflator.
3. Unwind power cord from the storage compartment of the unit and insert the DC plug into the 12V socket of your vehicle or use the AC cord into a wall socket.
   • Turn the AC/DC switch to the when using the AC plug or to the when using the DC plug.
   • Press the air pressure unit button to toggle between BAR, PSI, KP A.
   • To stop the tire inflator before it reaches the preset pressure, set the power switch to the "O" position.
4. Pull air hose from compartment.
5. For vehicle tires: Unlock thumb latch of air nozzle by moving to vertical position (see diagram below) and place air nozzle over valve stem of tire.
   
6. Push air nozzle down firmly onto valve stem and quickly lock into place by pressing thumb latch to horizontal position.
   
7. For other inflatable items: Select the appropriate adaptor and insert it into the unlocked air nozzle. Lock air nozzle with thumb latch.
   Tip: When inflating athletic balls, moisten needle before inserting it into the ball valve.
8. Press the "+" or "−" buttons to set the desired pressure. When the LCD screen is displaying the target PSI, the LCD readout will blink 3 times at the desired preset pressure, and it will then change back to the current pressure of the item that you are inflating.
   • Press the air pressure unit button to toggle between BAR, PSI, KPA.
9. Set the power switch to the "|" position to start the inflator. The inflator will shut off automatically at the desired pressure that you have programmed. The preset pressure can be changed during inflation by pressing the pressure adjusting buttons (+/−) to the new desired pressure.
   • To stop the tire inflator before it reaches the preset pressure, set the power switch to the "O" position.
10. Once the inflator has shut off, set the power switch to the "O" position.
11. Disconnect the valve adapter and power cord once the inflation is complete. Store your tire inflator.

DO NOT OVERINFLATE PRODUCTS BEYOND THE MANUFACTURER'S RECOMMENDATIONS.

NEVER LEAVE INFLATOR UNATTENDED WHILE IN USE.

CARE AND MAINTENANCE

• Use only mild soap and a damp sponge to clean compressor.
• Do not immerse any part in liquid.

SPECIFICATIONS

TROUBLESHOOTING

CAUTION

• Do not overheat the unit! If the inflator is not pumping a steady stream of air and appears sluggish or if metal fittings get too warm to the touch, these are indicators that the inflator has been in operation for too long. Immediately turn off the inflator and allow it to cool for approximately 30 minutes before resuming operation. Never leave inflator unattended while in use.
• Do not over inflate items beyond their needs. Most car tires will inflate properly between 30 and 35 psi depending upon the tire. Some racing bicycle tires require pressure in excess of 75 psi. Other bicycle tires may require substantially lower pressures. This unit is not fitted for highpressure tires such as those used on large commercial trucks.
• Keep out of reach of children.
• Plug into a 12V DC socket or a 120V AC socket, but NEVER both at the same time.

31088 San Clemente Street
Hayward, CA 94544, U.S.A.

Tel: +1.510.471.9221
U.S. & Canada Toll Free: +1.800.231.5806
customerservice@wagan.com
www.wagan.com

Documents / Resources

References

• Wagan Corp | Wagan Corporation

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download WAGAN Tech 7316 - AC/DC DIGITAL TIRE INFLATOR Manual