English - IKEA MITTZON Manual

English

An electro-mechanical height-adjustable work surface with a control interface to adjust the
height up and down. This product can be used by children aged from 14 years and above
and persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the product
in a safe way and understand the hazards involved by a person responsible for their safety.
Children shall not play with the product. Cleaning and user maintenance shall not be carried
out by children without supervision.
Translated from the original instructions.
Advice and instructions for MITTZON sit/stand desk.
Model:
Input:
Sound level:
Standby power consumption:
Height setting interval:
Maximum load:
Temperature interval at usage:
Temperature interval at storage:
Humidity:
Power supply unit:
This product shall only be used together with the included power supply
unit.
Every person who is responsible for this table at installation or employment of
the table in daily use or in service and repair work should carefully read these
instructions. Keep these instructions close to your sit/stand table.
Installation instructions
The table is assembled according to separate assembly instructions. Connect
one side of the 90-degree connection cable (50mm long) to the M1 port
on the control box, then connect the other side to the cable from the leg.
Connect the cable from the other leg to the M2 port on the control box.
Connect the hand controller to the HS port and the power supply to the AC
port on the control box. The control box should be placed in the tray created
by the frame, and the electrical cable should be placed in the felt tray on the
back. Position the electrical cable so it does not get damaged. Please check
the assembly instructions. Connect the electrical cable to a wall socket (or a
socket placed in the felt tray).
Note! The electrical cable must have full mobility.
The table is now ready for use. The motors will stop automatically when the
table reaches its lowest or highest position respectively.
Usage of the table
The table shall only be used as a working table with the possibility to
continuously adjust the working height between sitting and standing
positions. The table shall only be used indoors and in dry premises (office
environment or similar).
The table must not be overloaded - maximum load is 80 kg/176 lbs.
The motors may be run continuously for a maximum of 2 minutes.
Afterwards, the motors must rest for approx. 18 minutes. before they can
be used again.
Follow these instructions when adjusting table height:
1. Make sure all cables are connected firmly in place.
2. Make sure no objects are in the way of the table so that the height can
adjust freely.
3. Press the up/down buttons on the hand controller to adjust the desk
height.
MITTZON
AC 110V or 230V, 50/60Hz
Lower than 50 dB(A)
<0.2W
62~126 cm, 24.4~49.6 in
80 kg/176 lbs
+5 up to +40 °C/41 up to 104°F
-10 up to +50 °C/14 up to 122°F
20% up to 80% at +30 °C/86°F
DC max 30V, 350W
Safety regulations
When the table moves up/down, keep the necessary safety distance to avoid
the risk of entrapment between the moving table top and fixed objects in
the surrounding area. When the table moves up/down, the user shall keep
watch so that nobody is injured or no object is damaged. The table top must
not be blocked by a fixed object which may risk that the table overturns.
Always remove any office chair before the table moves up/down. The table
tripod must not be altered or reconstructed in any way. In service and repair
work of the table, the electrical cable must always be disconnected from the
wall socket (the connected socket). Alterations to the control box and hand
controller are absolutely forbidden! Alterations to the legs are absolutely
forbidden! The table must not be used as a hoisting device for persons.
Maintenance and repair instructions
After approx. 1 week of use, check that the screws are properly tightened. If
the table cannot be lowered or raised, check the connections between the
desk power plug and the wall socket (the socket) and ensure that all cables
are connected firmly in place. If any part of the electrical height-adjustable
table needs to be replaced, the electrical cable must be first disconnected
from the wall socket (the socket). After finishing the replacement, then
connect the electrical cable to the wall socket (the socket) and then finish the
reset process according to the reset instructions. After resetting successfully
without any problems, the table is ready for use. If the table still does not
work, please contact your nearest IKEA store or customer service.
Product servicing
Do not attempt to repair this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks.
Manufacturer: IKEA of Sweden AB
Address: Box 702, SE-343 81 Älmhult, SWEDEN
Telephone no.: +46(0)476-648500
SAVE THESE INSTRUCTIONS
The crossed-out wheeled bin symbol indicates that the item should be
disposed of separately from household waste. The item should be handed
in for recycling in accordance with local environmental regulations for waste
disposal. By separating a marked item from household waste, you will help
reduce the volume of waste sent to incinerators or landfills and minimise any
potential negative impact on human health and the environment. For more
information, please contact your IKEA store.
EU Declaration of Conformity is included in the packaging as a separate
document.
4