Protocol Insight HS-G5 Quick Start And User Manual
Hide thumbs
Also See for HS-G5:
- Quick start and user manual (17 pages) ,
- Quick start user manual (14 pages)
Table of Contents
Advertisement
Quick Links
HS-G5 Amp Splitter (FG5AMPSP)
Copyright © Protocol Insight. All rights reserved. Licensed software products are owned by Protocol
Insight or its suppliers and are protected by national copyright laws and international treaty
provisions.
Protocol Insight products are covered by U.S. and foreign patents, issued, and pending. Information
in this manual supersedes all previously published material. Details, specifications, and pricing
subject to change.
Protocol insight is a registered trademark of Protocol Insight, LLC.
MIPI and the MIPI logo are a licensed trademark of the MIPI Alliance.
UFSA and UFS Logo are a trademark of the Universal Flash Storage Association
JEDEC® and the JEDEC logo are registered trademarks of JEDEC Solid State Technology Association.
Contact Protocol Insight at:
sales@protocolinsight.com
support@protocolinsight.com
www.protocolinsight.com
Product specifications and descriptions in this document are subject to change without notice.
Quick Start / User Guide
© Protocol Insight, LLC 2022, Revision 1.3.0, February 2024
1
Advertisement
Table of Contents
Related Manuals for Protocol Insight HS-G5
Summary of Contents for Protocol Insight HS-G5
- Page 1 HS-G5 Amp Splitter (FG5AMPSP) Quick Start / User Guide Copyright © Protocol Insight. All rights reserved. Licensed software products are owned by Protocol Insight or its suppliers and are protected by national copyright laws and international treaty provisions. Protocol Insight products are covered by U.S. and foreign patents, issued, and pending. Information in this manual supersedes all previously published material.
-
Page 2: Table Of Contents
Switch Setting Frequency Response Linear ................... 11 Phase-Matched Cables ..........................12 Operating Conditions..........................13 Contact Information ..........................13 Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 3: Introduction
The “33” side is then amplified and sent to the protocol analyzer. The amplification settings are adjustable. Control Status Reset Figure 1 – FG5AMPSP Production Board Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 4: Use Case Requirements
EYE diagram requirements at the probing point for GEAR3, GEAR4, GEAR5 signal IGURE rates. Figure 2 - EYE Diagram Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 5: Connecting The Amp Splitter
Sublink 0 Rx0 and Rx1, respectively. PA0 and PA1 on the second FG5AMPSP board should connect to Sublink 1 Rx 0 and Rx1, respectively. Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 6: Onboard Switch Settings
Recommended Disabled 1100 Recommended Enabled -1.6 -0.8 1101 Recommended Enabled -1.6 1110 Recommended Enabled -0.8 1111 Recommended Enabled Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 7: Status Lights
Status light #3 will briefly illuminate during power-up and will stay lit whenever the microcontroller encounters an error. If Status light #3 is illuminated, you must power cycle the board to clear the Contact Protocol Insight if Status light #3 continues to illuminate after repeated power error state. -
Page 8: Recording Traffic
4-bit switch as previously described. Recording Traffic You can use the Instrument Status counters in the Protocol Insight software to adjust the amp splitter lane amplifier settings. You can also use the Smart Tune™ equalization settings to further optimize the lanes. -
Page 9: Maintenance - Offset Cancellation
PA0 or PA1 is greater 3mV, please contact Protocol Insight technical support, refer to ONTACT NFORMATION Figure 4 Offset Cancellation Measurement Setup Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 10: Switch Setting Frequency Response Log
Switch Setting Frequency Response Log Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 11: Switch Setting Frequency Response Linear
Switch Setting Frequency Response Linear Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 12: Phase-Matched Cables
Min Bend Radius Dynamic 23.3 mm Temperature Range -55 – 125 C Figure 5 - Cable Loss Over Frequency Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024... -
Page 13: Operating Conditions
2. Support materials and examples files are available at http://www.protocolinsight.com/support-materials/ 3. For technical support please contact your local Protocol Insight representative or support@protocolinsight.com Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2022, Revision 1.3.0, February 2024...
Need help?
Do you have a question about the HS-G5 and is the answer not in the manual?
Questions and answers