Page 1
3. Disassembly and Reassemble 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram B1930HD / B2030HD / B2230HD / B2330HD / B2430HD Refer to the service manual in the GSPN (see the rear cover) for the more information.
Page 4
3. Disassembly and Assembly 3. Disassembly and Assembly This section describes the disassembly and reassembly sequences for this monitor. Warning: As this monitor has parts that are sensitive to static electricity, be careful when handling them. 3-1. Disassembly Caution: 1. Turn the monitor off before beginning the disassembly process. 2.
Page 5
3. Disassembly and Assembly Description Photo Screws 3. Turn the monitor over again .
Page 6
3. Disassembly and Assembly Description Photo Screws 4. Turn the monitor over again to remove the back cover. 5. After disassembling the Rear-Cover, prepare for the internal disassembly as shown in the picture on the right. LVDS LAMP WIRE Screws Function&Speaker wire 6.
Page 7
3. Disassembly and Assembly Description Photo Screws 8. Remove the Function & SPK wires. 9. Remove the SPK upwards. 10. Remove the Assy Shield-Cover. Disassemble the PCB inside the Assy. 11. Disassemble the panel. ※ Reassembly procedures are in the reverse order of disassembly procedures.
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than two people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2. Product specifications 2-1. Feature & Specifications Feature Supreme Digital Interface & Networking ሪ - With a built-in ATV tuner, it supports TV with no particular set-top box and provides simple access with a single remote control. Excellent Picture Quality ሪ...
& BN59-01012A Batteries (AAA x 2) 3903-000452 & Power Cord 3903-000440 (Australia) Stand Body BN96-12487A Stand Base BN96-12485A Samsung Electronics Service center D-Sub Cable BN39-00244H BN59-01091A User’s Guide, & Monitor Driver, BN59-01091F Natural Color Pro Software (Australia) Cleaning Cloth BN63-01798B...
4. Troubleshooting 4. Troubleshooting 4-1. First Checklist for Troubleshooting Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Turn off both your computer and the monitor. Unplug the video cable from the back of the computer Turn on the monitor.
4. Troubleshooting 4-2. No Power The LED on the front panel of the monitor does not work when the power is connected and the Symptom Power button is pressed. Check if the Power switch on the rear panel of the monitor has been turned on. Check the SMPS fuse and the IP-Board output power.
Page 28
4. Troubleshooting 4-2-1. Circuit diagrams when the power does not turn on...
Page 29
4. Troubleshooting 4-2-2. Waveforms ① ②...
4. Troubleshooting 4-3. PC (ANALOG) No Screen The LED power is on but no picture is displayed on the screen when the D-SUB cable is Symptom connected Even though the LED power turns on, the screen is blank when connecting the VGA cable. Check the D-sub cable connections.
Page 31
4. Troubleshooting 4-3-1. Circuit diagrams and waveforms (Analog) when no screen is displayed on the monitor...
Page 32
4. Troubleshooting Analog PC 4-3-2. Waveforms when no screen is displayed ( ④ ⑤...
4. Troubleshooting 4-4. DVI/HDMI No Screen The LED power turns on but the screen is blank when the HDMI cable is connected. Symptom Check the HDMI cable connections. Check whether the LVDS cable is connected correctly to the panel. Major checkpoints Check whether the lamp connector of the panel is connected correctly to the IP board.
Page 34
4. Troubleshooting 4-4-1. Circuit diagrams and waveforms (DVI/HDMI No Screen) when no screen is displayed on the monitor...
Page 35
4. Troubleshooting 4-4-2. Waveforms when a blank screen is displayed (DVI/HDMI No Screen) ⑧ ⑨ 4-10...
4. Troubleshooting 4-5. Faults and Corrective Actions Fault Photo Symptoms and Corrective Actions Remarks Symptoms: DVI signals are not recognized. * Refer to the Training Manual for information on inputting the DVI DDC. Causes: This fault occurs when the PC does not recognize the mode information because the DVI DDC has not been input to the monitor.
4. Troubleshooting 4-6. Adjustment 4-6-1. Service Instruction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3. Correct impedance matching is essential. 4.
Page 38
4. Troubleshooting 4-7-3. Sub-Page of Service - OPTION - SVC - ADC/WB - Control 4-13...
4. Troubleshooting 4-8. White Balance - Calibration 4-8-1 White Balance -Calibration 1. Calibration PC Calibration 4-8-2 Service Adjustment - You must perform Calibration in the Lattice Pattern before adjusting the White Balance. Color Calibration Adjust spec. 1. Source : PC 2.
4. Troubleshooting 4-8-3 White Balance - Adjustment (low light) (hight light) Sub Bright Sub Contrast 3. W/B R offset R gain G offset G gain B offset B gain (W/B adjustment Condition refer next page) 4-9. White Ratio (Balance) Adjustment You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
4-10. Servicing Information 4-10-1 USB Download Method Samsung may offer upgrades for TV’s firmware in the future. Upgrades will be possible by connecting a USB drive to the USB port located on your TV. Insert a USB drive containing the firmware upgrade into the USB port on the rear of the TV.
4. Troubleshooting 4-11. Software Upgrade 4-11-1. Program Upgrading - MAIN 1. If you select MENU → Support → Software Upgrade on remote control, you’ll see below picture 2. Press ENTER, then you’ll see below picture. Select Yes 3. Micom program is now upgrading as below picture. After Software Upgrade is process by 100%, the monitor is automatically turn off and on.
Page 43
4. Troubleshooting 4-12. Micom Program Upgrade DDC Manager Connection 1. Prepare PC to Upgrade the Program. PC for MCU upgrading Connect to Parallel port 2. Prepare the DDC Manager 3. Connect D-sub cable to Target Monitor TV 4. Power on the Target Monitor TV winDDC_V2-39 Program installed Run winDDC 4-18...
Page 44
1. Select WinISP Menu 2. Make same setting like picture. 3. Choose Device Type. - 30-MFM(B1930HD/B2030HD/B2230HD/B2330HD/B2530HD:WT61P8 4. Load File ( Select file to download) 5. Set Option to load Binary Files 6. Select files (hex file) 7. Click button to load files...
Page 45
4. Troubleshooting 8. Check the OK message (Load) 9. Click Auto Program button 10. If you see OK message (Verify), program download is completed 4-20...
6. Wiring Diagram 6-2. Board Connection - Main Board Connect with IP LVDS Connector board (Connect to Panel) Common Interface (CI-Slot) * EU models only USB (Program Headphone Update) PC Stereo HDMI / DVI PC Analog Digital Audio EXT In/Output Output (Scart) (Optical)
* When a problem occurs: The No USB Download Operating error may occur. CN801 Component Audio input terminal. * When a problem occurs: The No Speaker Output error may occur. CN1301 Headphone output terminal. 6-4. Cables LVDS 30P FFC cable Item B1930HD / B2030HD B2230HD B2330HD B2430HD Code BN96-12453S BN96-12453R BN96-12453Q BN96-12453P...