Related Manuals for SCI WLS350 Series
Summary of Contents for SCI WLS350 Series
- Page 1 WLS350 Series Load Weighing System Basic Installation, Calibration and Operating Instructions WLS350 Installation Calibration & Operating Instructions V1.0...
-
Page 2: Important Safety Information
Service, Operation, or Maintenance Manuals. It is your sole responsibility to install, operate, and maintain the SCI system in a manner that will not cause damage to persons, property, or anything else. Always use safe practices and adhere to any laws that may be in place. -
Page 3: Table Of Contents
WLS350 Series Load Weighing System Manual Table of Contents Important Safety Information ....................A Table of Contents ........................1 Introduction ........................2 1.1. Components ....................... 2 Installation Procedure for the WLS350 ................3 2.1. Fitting the Display to the Operators Cabin ............... 3 2.2. -
Page 4: Introduction
WLS350 Series Load Weighing System Manual Introduction The WLS350 Weighing Indicator is IP67 rated digital indicator designed for use on forklifts and small wheel loaders in temperatures between -40F – 185F degrees. Operating Voltage is 8-32 Volts DC. The WLS350 will generally be installed with a hydraulic pressure transducer mounted in the piston / ram side of the lift circuit cylinder. -
Page 5: Installation Procedure For The Wls350
WLS350 Series Load Weighing System Manual 2. Installation Procedure for the WLS350 WARNING: These basic installation instructions are given based on the installer having previous experience in the servicing and maintenance of machinery. General safety precautions should be undertaken similar to carrying out maintenance on this type of machinery. -
Page 6: Establishing A Weighing Point
WLS350 Series Load Weighing System Manual 2.4. Establishing a Weighing Point The WLS350 is a static scale. Because it uses hydraulic pressure from the lift cylinders to determine weight, a fixed point must be selected for accurate results. Recording weights from positions other than this fixed point, will provide inaccurate results. -
Page 7: Basic Calibration Instructions
WLS350 Series Load Weighing System Manual 4. Basic Calibration Instructions The calibration instructions below are given based on a typical installation. This system can be used in a large variety of applications, and changing the parameters that are set will greatly affect the performance of this scale. -
Page 8: Basic Weighing
WLS350 Series Load Weighing System Manual 5. Basic Weighing NOTE 1: All reference to weighing position refers to raising the forks or bucket up to a pre- determined position and lowering slightly and slowly. The pre-determined position is determined by the installer and is generally indicated by stickers on the mast (Raise to 1, Lower to 2) and on the carriage. -
Page 9: Home
WLS350 Series Load Weighing System Manual 6. Home Page Layout Info Settings Accumulate Figure 3 Zero Clear Current Load WWW.SCALEANDCONTROL.COM... -
Page 10: Settings
WLS350 Series Load Weighing System Manual 7. Settings Page Layout Figure 5 Decrement / Previous Value – Lowers selected value or changes to previous value Cycle Setting – Moves the Selection Box in a cycle around the settings page Set / Enter – Sets Pressures Return to Home –... - Page 11 WLS350 Series Load Weighing System Manual Appendix A – Hydraulics Adapter Size Identification Chart Pipe Pipe Size Thread Wrench Thread Wrench Thread Wrench Thread Wrench 7/16-20 9/16 9/16-18 11/16 1/4-18 11/16 7/16-20 9/16 9/16-18 11/16 11/16-16 13/16 3/8-18 9/16-18 11/16...
- Page 12 WLS350 Series Load Weighing System Manual Flange, JIC, flat face O-ring WWW.SCALEANDCONTROL.COM...
- Page 13 WLS350 Series Load Weighing System Manual BSPP Chart DIN Chart WWW.SCALEANDCONTROL.COM...
- Page 14 WLS350 Series Load Weighing System Manual NOTES WWW.SCALEANDCONTROL.COM...
- Page 16 Contact us today! Toll Free: 888-239-0552 support@scaleandcontrol.com www.scaleandcontrol.com ©Copyright 2024 Scale and Control Inc. – All Rights Reserved...