Download
Share
Print this page
Wolf PI363418 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Wolf Manuals
  4. Ventilation Hood
  5. PI363418
  6. Installation instructions manual

Wolf PI363418 Installation Instructions Manual

Pro island ventilation hoods
Hide thumbs Also See for PI363418:

Advertisement

Quick Links

Download this manual See also: User Manual
P
I
V
H
R O
S L A N D
E N T I L A T I O N
O O D S
I
I
NSTALLATION
NSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS

Advertisement

loading

Related Manuals for Wolf PI363418

Summary of Contents for Wolf PI363418

  • Page 1 S L A N D E N T I L A T I O N O O D S NSTALLATION NSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS...
  • Page 2 ® WOLF is a registered trademark of Wolf Appliance, Inc. WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite.

  • Page 3: Warning - To Reduce The Risk Of Fire, Electric Shock, Or Injury To Persons, Observe The Following

    Use & Care Information prior to use. Any questions or problems about the installa- tion should be directed to your Wolf dealer or Wolf Appliance, Inc. at 800-332-9513. You can also visit our website at wolfappliance.com.
  • Page 4 Wolf internal, in-line and remote blower assemblies are available; refer to pages 15–16. Use only a Wolf blower with the Pro island hood. IMPORTANT NOTE: Wolf recommends that the Pro island ventilation hood be installed 30"...
  • Page 5 E L E C T R I C A L R E Q U I R E M E N T S Wolf Pro island ventilation hoods require a separate, grounded 110/120 V AC, 60 Hz power supply. The service should have its own 15 amp circuit breaker.
  • Page 6 P R O I S L A N D V E N T I L AT I O N I N S TA L L AT I O N The illustration and chart below provides dimensions critical for proper installation of the Wolf Pro island ventilation hood. 13" (330) HEIGHT OF TRANSITION 34"...
  • Page 7 Use duct sealing tape on joints between ductwork sections. Wolf Pro island hoods come standard with a backdraft damper included in the transition assembly. Local codes may require the use of an additional backdraft damper.
  • Page 8 W O L F P R O I S L A N D V E N T I L AT I O N I N S T A L L C E I L I N G F R A M I N G IMPORTANT NOTE: If an optional duct cover is to be used, it must be installed before installing the island hood.
  • Page 9 10. Duct covers 6" (152), 12" (305), 18" (457) and 24" (610) high in widths to match all island hoods are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.
  • Page 10 W O L F P R O I S L A N D V E N T I L AT I O N H O O D P R E P A R A T I O N Follow these steps to prepare the island hood for installation: Remove the filters by pressing up at the angle the filters are placed in, then rotate...
  • Page 11 Make the electrical connections. Refer to Install Wiring on pages 13–14. A C C E S S O R I E S Optional acces- sories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.
  • Page 12 W O L F P R O I S L A N D V E N T I L AT I O N I N S T A L L T H E I N S TA L L AT I O N W I T H O U T D U C T C O V E R Lift the hood and align the hood mounting holes with the predrilled holes in the framing.
  • Page 13 I N S TA L L AT I O N I N S T R U C T I O N S I N S T A L L W I R I N G Risk of electrical shock. This ventilation hood must be properly grounded.
  • Page 14 W O L F P R O I S L A N D V E N T I L AT I O N I N S T A L L W I R I N G I N - L I N E O R R E M O T E B L O W E R W I R I N G Remove the hood electrical box cover.
  • Page 15 Locate the blower so that the length of the duct run and number of elbows and transitions are kept to a minimum. Wolf recommends the maximum linear duct run be no greater than 50' (15 m).
  • Page 16 I N - L I N E B L O W E R R E M O T E B L O W E R S Refer to the Wolf Design Guide for Pro ventila- tion recommendations. You can also visit our website at wolfappliance.com.

  • Page 17: Side View

    F I LT E R I N S T A L L A T I O N Follow these instructions to install filters and grease cups for Wolf Pro island hoods: Reinstall the internal frame. Refer to Hood Preparation on page 10.
  • Page 18 Maintain the quality built into your Pro island ventilation hood by calling a Wolf authorized service center. For the name and number of the Wolf authorized service center nearest you, check the Locator section of our website, wolfappliance.com, or call Wolf Customer Service at 800-332-9513.
  • Page 19 LEFT OUTER EDGE OF HOOD...
  • Page 20 W O L F A P P L I A N C E , I N C . P. O . B O X 4 4 8 4 8 M A D I S O N , W I 5 3 7 4 4 8 0 0 - 3 3 2 - 9 5 1 3 W O L FA P P L I A N C E .

This manual is also suitable for:

Pi423418Pi543418Pi663418Pi363418rPi423418rPi543418r ... Show all