Advertisement
Quick Links
INSTALLATION INFORMATION
EMG MODEL: 707-TW
SPECIFICATIONS:
Logo Color
Magnet Type*
Resonant Frequency (KHz)
Output Voltage (Finger, Thumb)
Output Voltage (Thump)
Output Noise (60 Hz)
Output Impedance (Kohm)
Current @9V (Microamps)
Battery Life (Hours)
Maximum Supply (Volts DC)
Installation notes:
The EMG-707-TW has a variety of ways it can be wired into a guitar. The diagrams included are limited to the most popular because of space.
The additon of the plug-on PC Board on the Push-Pull Pot adds further flexibility as you will see in the diagrams. The Push-Pull Pot can be used
as a volume control or a tone control, and as a pickup control or master control for either. See pages 2 and 3 for details on how to configure
your Push-Pull Pot for a given configuration. More wiring diagrams are available at emgpickups.com.
Included with each pickup:
1 TONE CONTROL (25K)
.235
(6)
.390
.310
(8)
(10)
STEREO OUTPUT
JACK
Warranty
All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If
upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This
warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.
© 2014 Copyright EMG INC. All Rights Reserved.
MODEL:
707-TW
Single-Coil
Copper
Alnico
3.76
1.00
3.00
-107
10
160
1500
27
1 TW P/P SWITCH
2 PICKUP IN/ OUT
W/POT (25K)
BATTERY BUSS
ADJUSTMENT SCREWS
MAXIMUM RECOMMENDED STRING WIDTH 2.50" (63.5)
.125 (3.17) DIA. MOUNTING HOLES
.750
(19.0)
Dual-Coil
1.80
2.00
4.50
-109
10
In Dual-coil mode, coils C1 and C2 are active.
In Single-coil mode, coils C2 andC3 are active.
TW PICKUP CABLE 15" (38cm)
2 CONNECT CABLES 5.5" (14cm)
OUTPUT CABLE 6" (15cm)
BATTERY
BUSS
BATTERY CABLE 7" (18cm)
- 9V +
3.500
(88.9)
3.250
(82.5)
.880
EMG-707-TW (SIDE VIEW)
C1 C2
C3
R .125
TYP
1.500
(38.1)
(22.3)
Advertisement
Related Manuals for EMG 707-TW
Summary of Contents for EMG 707-TW
- Page 1 Installation notes: The EMG-707-TW has a variety of ways it can be wired into a guitar. The diagrams included are limited to the most popular because of space. The additon of the plug-on PC Board on the Push-Pull Pot adds further flexibility as you will see in the diagrams. The Push-Pull Pot can be used as a volume control or a tone control, and as a pickup control or master control for either.
- Page 2 The Push-Pull Switch included with the TW Pickup allows you to choose between SINGLE COIL ON: UP POSITION two internal pickups of the EMG-TW, single-coil and dual-coil. The Push-Pull Pot has two seperate sections: The Switch and the pot, described below.
- Page 3 INSTALL SHUNT ON (H4) as needed onto headers H1 thru H6. Use Diagram #5 if you have a single 707-TW installed in your instrument, or have two or more pickups in your instrument and want to use the pot as the PICKUP OUTPUT: Tone control for the 707-TW Pickup only.
- Page 4 Refer to Diagram #11 Below: 1) Install the Pickups and route the cables to the control cavity keeping 1) Install the 707-TW Pickups and route the cables to the control cavity keeping any excess cable under the pickup. any excess cable under the pickup.