Related Manuals for SI Pegasus
Summary of Contents for SI Pegasus
- Page 1 FCC ID: 2ASYG-PEGASUS1 COMPAT LOCAL R.RX R.TX CHANNEL LEARN PROG DATA Pegasus Installation Instructions 400243 | v. 1.0 | 29 August 2023...
- Page 2 Video Tutorials related to the product. Tech Specs Scan the QR code to scan Pegasus specsheet FCC INFORMATION This device complies with FCC RF radiation exposure limits set forth for general population. This device must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located in conjunction with any other antenna or transmitter.
-
Page 3: Table Of Contents
CONTENTS Parts in the Box Mounting Options RJ45 and Power Pinouts GPI/O and Dry Contact Pinouts IR HEX codes LED Details User Button Actions Learning Somfy/Olibra Remotes, Keypads & Sensors Learning Pico Remotes to Control a 485 Motor Programming an RTS Motor Channel RTS Smart Repeater Setup RTS to 485 Smart Receiver Setup 485 to RTS Smart Transmitter Setup... -
Page 4: Parts In The Box
PARTS IN THE BOX (1) Pegasus (1) White Decora (1) Pegasus Decora Label Wall Trim Plate (1) CAT5e (2)Trim plate (2) J Box (1) AUX USB screws screws Power Cable... -
Page 5: Mounting Options
MOUNTING OPTIONS Choose your mounting: Standard single or Left or Right Din Rail multiple gang J Box mounting Pegasus Pro-tip It is best not to mount Pegasus in a metal J Box... -
Page 6: Rj45 And Power Pinouts
RJ45 AND POWER PINOUTS 5 position removable screw-down Terminal block connector for GPI/O Aux power Input (7-28vDC) FCC ID: 2ASYG-PEGASUS1 COMPAT LOCAL R.RX R.TX CHANNEL LEARN PROG DATA - Ground (USB Black) +7-28vDC Positive (USB Red) 485 Connection (TIA 568B) RJ Pin Outs Data +(WHT/ ORG) Data - (ORG) -
Page 7: Gpi/O And Dry Contact Pinouts
GPI/O AND DRY CONTACT PINOUTS 12 V Trigger Dry Contacts Tip DC Sleeve 0 - 10V Input GND (PINK) (-) DOWN POSITIVE (VIOLET) (+) IR Input GREEN(DATA +(VSI) STOP YELLOW (IR/SERIAL+)(485 DATA -(SIG OUT)) BLACK (IR/SERIAL-)(GND ) -
Page 8: Ir Hex Codes
IR HEX CODES Third party IR universal control systems may be used to control the screen or using these hex codes: (Available on the website too.) * Not included / optional 0000 006c 0000 000c 0006 011b 0006 011b 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 08a4 0000 006c 0000 000c 0006 011b 0006... -
Page 9: Led Details
LED DETAILS Local Mode Repeater Mode Receive (Rx) ON when in Local Mode On SOLID when IN Repeater RX Mode Compatible Mode Repeater Mode Transmit (Tx) ON when in Compatible On SOLID when IN Repeater Mode FCC ID: 2ASYG-PEGASUS1 RX Mode COMPAT LOCAL R.RX... -
Page 10: User Button Actions
LOCAL R.RX R.TX (erases all channels in and out and CHANNEL LEARN PROG puts Pegasus back in Local mode and Learn Button Legacy compatibility) Press this button (LED starts DATA flashing) to LEARN a Sub GHz HEX Switch Fixed Channels... -
Page 11: Learning Somfy/Olibra Remotes, Keypads & Sensors
LEARNING SOMFY OR OLIBRA REMOTES, KEYPADS & SENSORS Use the Terminal Block or 485 Bus for power Ensure Compat LED is OFF Ensure the Local LED (red) is ON FCC ID: 2ASYG- COMPAT LOCAL R.RX Adjust the HEX(0-F) to the desired Channel to learn R.TX CHANNEL LEARN... -
Page 12: Learning Pico Remotes To Control A 485 Motor
LEARNING PICO REMOTES TO CONTROL A 485 MOTOR Use the Terminal Block or 485 Bus to power up Pegasus Ensure the Local LED (red) is ON FCC ID: 2ASYG- Check to see if the Compat LED is ON, if it is skip over... -
Page 13: Programming An Rts Motor Channel
Some RTS motors have a yellow LED that will begin flashing Next press the Prog button on Pegasus, and the motor will jog once confirming you have programmed the motor. You can now use the GPI/O inputs or 485 commands to test your... -
Page 14: Rts Smart Repeater Setup
RTS SMART REPEATER SETUP Use the Terminal Block or 485 Bus to power up Pegasus Ensure the Local LED (red) is ON FCC ID: 2ASYG- COMPAT LOCAL R.RX R.TX CHANNEL LEARN PROG Set HEX switch to channel E DATA Verify that Both the R.RX and R.TX LED’s turn on... -
Page 15: Rts To 485 Smart Receiver Setup
Connect a CAT 5e or greater 24AWG cable to one of the 485 data ports Any valid RTS RF signal will now come in, and then be formatted and sent out the 485 bus for other Pegasus configured as an RTS Smart Transmitter to re-transmit up to 4000’ away... -
Page 16: 485 To Rts Smart Transmitter Setup
485 TO RTS SMART TRANSMITTER SETUP Use the Terminal Block or 485 Bus to power up Pegasus Ensure the Local LED (red) is ON FCC ID: 2ASYG- COMPAT LOCAL R.RX R.TX CHANNEL LEARN PROG Set HEX switch to channel C DATA Verify that the R.TX LED turns on and stay lit... -
Page 17: Network Mode
NETWORK MODE Please connect Pegasus to a 485 bus port segment with a TRO.Y connected. Please refer to Pegasus Transceiver Configuration Section in TRO.Y / 2 Programming Manual. scan QR code... -
Page 18: Factory Reset
FACTORY RESET To factory reset Pegasus press and hold both the Learn and Programming buttons for approx 3 seconds until all led's come on. This will erase any remotes, or motors stored, switch modulation back to Legacy and place the Pegasus in the Local mode. - Page 19 Somfy Systems, Inc. We use the trademarks for the sole purpose of identifying products compatible with TRO.Y, Helen or Pegasus. This use does not imply any endorsement by or affiliation with the trademark owners.
- Page 20 Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com 400243 | v. 1.0 | 29 August 2023 Copyright 2019 US SHADE CORPORATION...
Need help?
Do you have a question about the Pegasus and is the answer not in the manual?
Questions and answers