Advertisement
SAFETY INSTRUCTIONS
For professional use only. Osbserve
all warnings. Read and unserstand all
instructions before operating equip-
ment. Extreme caution should be used
when operating this equipment as per-
sonol injury and/or property damage
can result from equipment misuse.
Adequate protection isrecommended
to prevent splashing of material onto
the skin or into the eyes.
WARNING
WARNING
NEVER point dispensing
valve at any part of the body or
at another person.
PRESSURE
RELIEF
PROCEDURE
To reduce the risk
of serious
bodily injury,
including
splash-
ing into the eyes or onto
the
skin, always follows
this proce-
dure
When ever you shut off the
pump,
when checking
or serv-
icing
any part of the system,
and when
installing,
cleaning
or changing
any part
of the
system.
1. Disconnect
air to the pump.
2. Point
the
dispensing
valve
away
from
yourself
and
others.
3. Open the dispensing
valve
into an appropriate
container
until pressure
is relieved.
If you suspect
that the dis-
pensing
valve or hose is com-
pletely clogged
or that pressure
has not been fully relieved
after
following
the above procedure,
VERY SLOWLY loosen the hose
end coupling
to relieve pressure
gradually,
then loosen comple-
tely.
Now clear the
valve or
hose.
WARNING
WARNING
NEVER try to stop or deflect
material from dispensing valve
or leakig connection or com-
ponent with your hand or body.
WARNING
ALWAYS check equipment
for proper operation before each
use, making sure safety devices
are in place and operating porp-
erly. DO NOT after or modify
any part of equipment as
this may cause amalfunction
and result in serious bodily
injury.
INSPECTION
INSTRUCTIONS
WARNING
ALWAYS follow the pressure
relief procedure after shutting
off the pump, when checking
or servicing any part of the sys-
tem; and when installing, clean-
ing or changing any part of the
system.
If overpressurizing
of the equipment
is believed to hav occurred, contact the
factory authorized warranty and service
center nearest you for inspection
of the
pump.
Specialized
equipment
and knowl-
edge is required for repair of this pump.
Contact the factory authorized warranty
and service center nearest you for repair
or adjustments
other than maintenance
specified
in this manual.
Annual
inspection
by the factory
authorized
warranty and service center
nearest you is recommended.
A list of factory authorized
warranty
and service centers
is available
upon
request.
DAMAGED
PUMPS
Any pump that appears to be damaged
in any way, is badly worn or operates
abnormally
shall be removed from use
until
repairs
are made.
Contact
the
factory authorized warranty and service
center nearest you for repairs.
INSTALLATION
The typical installation
shown is only
a guide for selecting
and installing sys-
tem components.
Contact your Lincoln
Representative
for assistance in design-
ing a system to suit your specific needs.
An air line filter/regulator/lubricator
isrecommended for use with your Lincoln
pump to remove harmful dirt and mois-
ture from the Compressed
air supply,
and to provide automatic
lubrication
to
the air motor.
This pump can develop
600
PSl working
pressure
at 200
PSl
maximum
incoming
air
pressure.
Be sure that all sys-
tem equipment
and accessories
are rated to withstand
the maxi-
mum working
pressure
of this
pump.
DO NOT exceed
the
maximum
working
pressure
of
the lowest
rated component
in
the system.
Flush the supply
lines and hoses
with mineral spirits or oil based solvent
and blow dry with air before connecting
them to the system. This is to purge any
contaminants
such as dirt, moisture, or
metal shavings that could damage the
pump or system components.
The pump was tested in lightweight
oil which was left in it to protect
the
pump from corrosion.
Flushing of the
pump before connecting
it to the sys-
tem might be desired to prevent
Pos-
sible contamination
of the fluid you are
pumping.
WARNING
To reduce
the risk of injury
from splashing
or static sparking
when
flushing
the pump
with
mineral
spirits
or oil based sol-
vent, always
hold a metal
part
of the dispensing
valve firmly
to the side of a grounded
metal
pail and operate pump at lowest
possible
fluid
pressure.
WARNING
ALWAYS read and follow the
fluid and solvent manufacture's
recommedndations
regarding the
use of protective clothing and
equipment.
Advertisement
