Related Manuals for EVB BCP-A2N-P
Summary of Contents for EVB BCP-A2N-P
- Page 1 OCPP EV Charger Installation Manual info@evb.com www.evb.com WWW.EVB.COM VERSION: 20231218-01...
-
Page 2: Table Of Contents
OCPP EV Charger Installation Manual OCPP EV Charger Installation Manual evb.com evb.com CONTENTS 1. Safety Information P-01 Important safety instructions P-01 ● 2. Product Introduction P-02 ● 2.1. Product Appearance P-02 2.2. Parameter table P-03 ● ● 2. . 3 Features P-04 2.4. -
Page 3: Safety Information
1. Safety Information 2. Product Introduction evb.com evb.com Important Safety Instructions Notes Ensure that the EV Charger's charging cable is positioned so it will not be stepped on, driven over, tripped on, or subjected to damage This document contains important instructions and warnings that must be followed when installing and maintaining the EV Charger. -
Page 4: Parameter Table
2.2. Parameter table 2.3. Features ● Connectivity: Ethernet and WIFI connection Wallbox Models BCP-A2N-P BCP-B2N-P BCP-AT2N-P BCP-BT2N-P ● Opened Up Detection: Once the charger is opened up, the charger stop charging and make alarm. ● App Remotes: Remotely control the charger and have the charging history. -
Page 5: Protection Functions
2. Product Introduction 2. Product Introduction evb.com evb.com 2.4. Protection Functions LTE-FDD:B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/B19/B20/B25/B26/B28 With full protection to avoid all kinds of charging safety hazards, it will automatic power off after the vehicle is fully charged, to protect the car Frequency Bands: battery and prolong the working life. -
Page 6: Installation Instructions
2. Product Introduction 3. Installation Instructions evb.com evb.com 3.1. Installation Considerations ● Note: Throughout the manual, "conduit" is used as the standard term for the protective tubing that houses the service wiring. In regions where conduit is not used (Europe for example), a cable comprised of service wiring enclosed in a protective jacket may be substituted for conduit if allowed by local regulations. -
Page 7: Power Supply
3. Installation Instructions 3. Installation Instructions evb.com evb.com 3.5. Power Supply 3.7. Installation Step 230V single-phase power supply 3.7.1. Step-by-step Installation Instructions (bottom entry wiring) 230V ● For single-phase EV charger, a single-phase wire (L), Neutral and earth wire must be connected. The phase voltage between the Line and Neutral wires should be 230V. - Page 8 3. Installation Instructions 3. Installation Instructions evb.com evb.com 3.7.2. Step-by-step Installation Instructions (rear entry wiring) 3.7.1. Step-by-step Installation Instructions (bottom entry wiring) wall Step 1 M6*8 bolts Drill Step 3 The 6 points Position Install the EV Charger to the mounting plate on the The bottom of the ⑨...
- Page 9 3. Installation Instructions 3. Installation Instructions evb.com evb.com 3.7.3. Step-by-step Installation Instructions (top entry wiring) 3.7.2. Step-by-step Installation Instructions (rear entry wiring) wall M6*8 bolts Step 1 Drill Step 3 Two points on Position the top and The bottom of the ⑨ positioning plate is 1.2 m away (recommended), if bottom of Install the EV Charger to the mounting plate.
- Page 10 3. Installation Instructions 3. Installation Instructions evb.com evb.com 3.7.3. Step-by-step Installation Instructions (top entry wiring) 3.7.4. External Meter Installation Warning ● Do not connect the power cord before reading and fully understanding all the concepts introduced in this section. If you are not sure whether the type of power supply on the repair panel is available, please consult an electrician for assistance.
-
Page 11: Sim Card Installation
3. Installation Instructions 4. Operating instructions evb.com evb.com 3.7.5. Set the Operating Current 4.1. Buttons On Charger Emergency stop button ● ● After installation, users can set the maximum operating current of the EV charger in the APP, Please refer to APP manual for details. -
Page 12: Led Lights Display
4. Operating instructions 4. Operating instructions evb.com evb.com 4.4. LED Lights Display Normal Status Normal Status Status Description LED Behavior LED Status Potential Cause Solution LED Behavior LED Status Status Description Potential Cause Solution Green lights up and The Charging... - Page 13 4. Operating instructions 4. Operating instructions evb.com evb.com Fault Status Fault Status Status Description LED Behavior LED Status Potential Cause Solution LED Behavior LED Status Status Description Potential Cause Solution All lights strobe Contactor failure Contactor adhesion Check whether Red light flashes...
-
Page 14: Firmware Update Via Ocpp Server
4. Operating instructions 5. Warranty evb.com evb.com 5. Warranty 4.5. Firmware Update via OCPP Server In order to ensure the normal service life of charging piles and reduce the risks in use, maintenance must be done within the specified time by The server sends a firmware upgrade command to the EV charger professionals with accredited safety maintenance tools.
Need help?
Do you have a question about the BCP-A2N-P and is the answer not in the manual?
Questions and answers