Safety And Protective Functions; Electromagnetic Radiation; Mechanical Movement; Emission - ebm-papst W1G200EC9110-CT1 Operating Instructions Manual

Part Number
W1G200EC9110-CT1
Operating Instructions
DANGER
Electrical load on the device
Risk of electric shock
 Stand on a rubber mat if you are working on an
electrically charged device.
WARNING
Terminals and connections have voltage even
with a unit that is shut off
Electric shock
 Wait five minutes after disconnecting the voltage
at all poles before opening the device.
CAUTION
The motor restarts automatically when operating
voltage is applied, e.g. after a power failure.
Danger of injury
 Keep out of the danger zone of the device.
 When working on the device, switch off the mains
supply voltage and secure the latter from being
switched on again.
 Wait until the device stops.
 After working on the device, remove any used
tool or other objects from the device.

1.5 Safety and protective functions

DANGER
Missing safety device and non-functioning safety
device
If there is no safety device, you could be seriously
injured, for example by reaching into the running
device with your hands.
 Operate the device only with a fixed and isolating
safety protection and a fixed guard grille. The
guard must withstand the kinetic energy of a fan
blade detaching at maximum speed.
 The safety device must be able to withstand the
kinetic energy of the fan during operation and
remain attached even at maximum speed levels.
Ensure gaps are not present during the
installation of the safety device to prevent
extremities (i.e. fingers) coming in contact with
the rotating components of the device during
operation.
 The device is a built-in component. You, the
owner/operator, are responsible for providing
adequate protection for the device.
 Shut down the device immediately if you detect a
missing or ineffective protective feature.

1.6 Electromagnetic radiation

Interference from electromagnetic radiation is possible, e.g. in
conjunction with open and closed-loop control devices.
If unacceptable emission intensities occur when the fan is
installed, appropriate shielding measures have to be taken by
the user.
NOTE
Electrical or electromagnetic interferences after
integrating the device in installations on the
customer's side.
 Verify that the entire setup is EMC compliant.
Item no. LS-188.
ebm-papst A&NZ Pty Ltd 10 Oxford Road · Laverton North VIC 3026 · Phone +61 (03) 9360 6400 · Fax +61 (03) 9360 6464
ABN 33 115 927 556 NSW Phone +61 (02) 9827 6400 · NSW Fax +61 (02) 9827 6464 · NZ Phone +64 (09) 525 0245 · NZ Fax +64 (09) 525 0246
sales@ebmpapst.com.au · www.ebmpapst.com.au

1.7 Mechanical movement

1.8 Emission

1.9 Transport

1.10 Storage

Store the device, partially or fully assembled, in a dry and

weatherproof manner in the original packing in a clean
environment.
 Protect the device from environmental impacts and dirt
until the final installation.
 We recommend storing the device for a maximum up to
one year to guarantee proper operation and longest
possible service life.
Even devices explicitly suited for outdoor use are to be

stored as described prior to being commissioned.
Maintain the storage temperature, see chapter 3.5

Transport and storage conditions.
Revision 001 Release 24/09/2018
DANGER
Rotating device
Body parts that come into contact with the rotor and
impeller can be injured.
 Secure the device against accidental contact.
 Before working on the system/machine, wait until
all parts have come to a standstill.
WARNING
Rotating device
Long hair, loose items of clothing and jewellery could
become entangled and pulled into the device. You
could be injured.
 Do not wear any loose clothing or jewellery while
working on rotating parts.
 Protect long hair by wearing a cap.
WARNING
Depending on the installation and operating
conditions, a sound pressure level greater than
70 dB(A) may arise.
Danger of noise-induced hearing loss
 Take appropriate technical safety measures.
 Protect operating personnel with appropriate
safety equipment, e.g. hearing protection.
 Also observe the requirements of local agencies.
NOTE
Transport of device
Take appropriate technical safety measures
 Transport the device in its original packaging
only.
Page 2 of 9