Advertisement
6
PROCEDURE FOR CONNECTION TO A PC
Connect the product to a PC with a commercially available USB 2.0 cable (mini B).
PC
(Note 2)
USB 2.0 cable (mini B) (Note 1)
Notes: 1) Please obtain a USB 2.0 cable (mini B) separately.
2) Select a USB 2.0 cable with a connector type on the PC side that matches the port on the PC.
1. Insert the connector of the USB 2.0
cable into the USB port on the product.
Do not apply stress, such as excessive bending or pulling, to the extracted part of
the USB 2.0 cable.
1. With the product secured in place, grasp
the connector of the USB 2.0 cable and
pull out.
Note: Do not apply excessive force to the cable part of the USB 2.0 cable.
7
SPECIFICATIONS
Product name
Model No.
Compatible controllers
Number of units connectable
Maximum of 15 controllers (one master, 14 slaves) per SC-HG1-USB unit
Supply voltage (Note 1)
Current consumption
Communication standard (Note 2)
Protocol
USB port
Protection
Pollution degree
Ambient temperature
-10 to +45°C (No condensation or icing), Storage: -20 to +60°C
Ambient humidity
Operating altitude
Material
Weight
Notes: 1) Power is supplied from a connected controller (master).
2) Varies depending on the PC operating environment.
3) Do not use or store in an environment that has been pressurized to an air pressure higher than the atmo-
spheric pressure at 0m.
Controller (Optional)
SC-HG1-USB
USB port (mini B)
USB 2.0 cable
1. Insert
USB port
1. Pull out
USB Communication Unit
SC-HG1-USB
HG-TC
24V DC ±10%, Ripple P-P 10% or less
50mA or less
USB2.0 Full speed
Dedicated Panasonic protocol
USB mini B
IP40 (IEC)
2
35 to 85% RH, Storage: 35 to 85% RH
2,000m or less (Note 3)
Unit case: Polycarbonate
Approx. 35g
8
CAUTIONS
This product is designed to be used with the HG-TC
product malfunctioning or damage may occur.
This product has been developed / manufactured for industrial use only.
and product damage. There is also a risk of a noticeable reduction of service life.
cluding controllers.
Do not use during the initial transient time after the controller power is switched
ON.
When noise generating equipment (switching regulator, inverter motor, etc.) is
used in the vicinity of the product, always connect the frame ground (F.G.) termi-
nal of the equipment to ground.
Do not wire the USB 2.0 cable (mini B) between the product and PC in parallel
with a high-voltage line or power line, or run through the same conduit. Risk of
malfunctioning due to induction.
Make sure the power is OFF while performing connection work.
This product is suitable for indoor use only.
Avoid dust, dirt, and steam.
Do not use in a location where there are corrosive or other harmful gases.
Ensure that the product does not come into contact with organic solvents such as
thinner.
Ensure that the product does not come into contact with strong acid or alkaline.
Ensure that the product does not come into contact with oil or grease.
sive gases.
Do not use the product in a location subject to intense vibration or shock.
This product is a precision device. Do not drop or otherwise subject to shock. Risk
of product damage.
Never attempt to disassemble, repair, or modify the product.
When the product becomes unusable or unneeded, dispose of the product appro-
priately as industrial waste.
For the procedures for using a connected PC, follow the instructions in the manual
provided with the PC.
Panasonic Industry Co., Ltd.
Panasonic Industrial Devices SUNX Co., Ltd.
https://panasonic.net/id/pidsx/global
Please visit our website for inquiries and about our sales network.
Panasonic Industrial Devices SUNX Co., Ltd. 202
, 202
-
-
PRINTED IN JAPAN
Advertisement
