Related Manuals for Celona AP 13
Summary of Contents for Celona AP 13
- Page 1 Installation Guide Celona Medium Power Access Point AP 13 © Copyright 2023 Celona Inc. All rights reserved.
-
Page 2: Table Of Contents
Phase and time synchronisation Supported frequency band Transmit power Data and voice connectivity Seamless session mobility Supported system bandwidth Troubleshooting Contacting Support Warranty Installation Guide Celona Medium Power Access Point AP 13 © Copyright 2023 Celona Inc. All rights reserved. - Page 3 About the AP Celona AP 13 is a 3GPP Release 15 compliant 4G Access Point (AP) with internal antenna that supports the 3550 – 3700 MHz Citizens Broadband Radio Service (CBRS)
-
Page 4: Interfaces
Installation Overview Network Design Plan The Celona AP 13 can be pole or wall mounted and has one integrated Each cell site may be unique in terms of the type and number of components 4-port 13.5 dBi 65D antenna. Before you mount and deploy your access to install, the coverage area, the user requirements, and so forth. -
Page 5: Leds
Installation Preparation LEDs The Celona AP 13 has 4 LEDs providing the following visual statuses for Power, Cellular status (1 and 2), Alarm. Color Status Description Steady on Power is on Green No power supply CELL1 is inactive CELL1 Green Fast flash: 0.1 s on, 0.1 s off... -
Page 6: Gps
-49°F to 158°F / -45°C to 70°C Humidity 5% to 95% RH Atmospheric Pressure 70 kPa to 106 kPa Safety voltage 42 V to 58 V Installation Guide Celona Medium Power Access Point AP 13 © Copyright 2023 Celona Inc. All rights reserved. - Page 7 Installation 1.6 in.–3.9 in. Some cell site structures may have existing frameworks for The AP 13 mounting bracket is assembled (40mm–100mm) attaching the AP. For purposes of explaining the installation before packing and includes two components: procedure, this section assumes the AP will be installed on a the preassembled bracket on the back of the support pole or on a wall.
- Page 8 Installation 3. Hold the AP 13 vertically and Follow the steps below to install the AP 13 on a pole. align the two pins on the AP 1. Unscrew the nuts of the pole mounting bracket, slide the 13 bracket with the pin holes two clamps to the left, and turn them up or down on the pole mounting bracket.
- Page 9 Follow the steps below to install the AP 13 on a wall. 1. Place the wall mounting bracket on the wall with arrow point up and mark the drilling location using a pencil or marker.
- Page 10 Connect Ground Cable General requirements: Prepare the grounding cable according to the actual measurements and requirements of the specific installation site. The AP 13 has two grounding • Bending radius of antenna feeder cable: 7/8” > 250mm, 4/5” > 380mm screws located on the bottom of the unit as shown below.
-
Page 11: Certified Professional Installation
(2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly The Celona AP 13 is a Class-B, FCC Part 96 certified device. Class-B devices are approved by the party responsible for compliance could void the user's authority required to be professionally installed by a Certified Professional Installer (CPI). - Page 12 Solution Architecture The high level architecture that enables the Celona AP 13 is shown below. The system consists of the essential functions detailed in Figure 1: System Architecture. The Celona Orchestrator performs AP Celona Spectrum authentication, validates the AP’s serial number, determines the...
-
Page 13: Configuring The Access Point
Celona Edge within the network on-premises or in the private/public cloud based on the site assignment. The AP will then connect directly to the Celona Edge and establish control and data plane connections. Once this is completed, the 4G LED on the AP will turn blue, signifying the private 4G network is operational. - Page 14 HTTPs connections with the Celona Orchestrator and IPSEC with the Celona Edge are provisioned at the factory. If the certificates on the Celona AP 13 need to be updated or replaced, the process is automatically triggered and managed by the Celona Edge. The certificates conform to the industry compliant X.509 standard.
- Page 15 Data Services Celona AP As seen in figure 2, mobile stations can obtain data and/or voice connectivity via the Celona Edge after the Celona AP 13 has its Packet Data Network for radio enabled. Celona AP 13 automatically data Sercices...
-
Page 16: Coverage Area
Transmit power 36.213 Release 12 – Physical layer procedures 36.214 Release 12 – Physical layer measurements The Celona AP 13 can transmit at a maximum power of 1 Watt per channel inclusive of internal gain. Supported frequency band Celona AP 13 supports frequency ranges from 3400 MHz to 3800 MHz. The... -
Page 17: Supported System Bandwidth
Operations and Maintenance Supported system bandwidth The AP 13 is a dual carrier eNodeB and is based on 4G Release 15. When the antenna configuration is arranged in such a way that overlapping coverage of two The Celona AP 13 supports two concurrent RF chains. The two RF chains provide orthogonal carriers exists, the AP supports two-component carrier aggregation two distinct cellular sectors. - Page 18 900 E Hamilton Ave Suite 200, celona.io Campbell, CA 95008, United States © Copyright 2023 Celona Inc. All rights reserved. Installation Guide Celona Medium Power Access Point AP 13 © Copyright 2023 Celona Inc. All rights reserved.