Related Manuals for Celona AP 20
Summary of Contents for Celona AP 20
- Page 1 Installation Guide Celona Indoor Access Point AP 20 Enabling cellular wireless connectivity for enterprise environments, within private spectrum options © Copyright 2023 Celona Inc. All rights reserved.
-
Page 2: Table Of Contents
Seamless session mobility Data and voice connectivity Coverage area Power save mode Transmit power Radio access technology Supported system bandwidth Troubleshooting Contacting Support Warranty Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved. -
Page 3: Introduction
A Subminiature Version A (SMA) coaxial RF connector port is available for GPS. If obtaining GPS lock is access point is designed for mission-critical use cases difficult, connecting a GPS puck to the Celona AP 20 may help achieve lock. The GPS puck is typically in indoor and semi-ruggedized environments. Like all... -
Page 4: Mounting
Mounting Installation Overview Mounting the Access Point The Celona AP 20 can be wall or ceiling mounted and has four omni- The Celona mount-kit supports several mounting methods, including directional internal antennas. Internal antennas are down-tilt toward from a suspended drop- ceiling, hard surface ceiling, and on a flat the front of the AP. -
Page 5: Install On Prelude And Suprafine T-Bar
Pull out the active grid bracket Fasten these two screws in the arrow direction M3*9 to prevent slipping Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved. - Page 6 Step 5: Fasten one M3*9 screw to fix device and mounting kit. Before slide the device Slide device by arrow direction to hold on M3*9 screw mounting kit. Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved.
-
Page 7: Install On Silhouette And Interlude T-Bar
Loosen these two M4*10 screws Screws M4*10 Screws M4*10 Pull out the active grid bracket in the direction of the arrow Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved. - Page 8 T bar. 1) Interlude’ XL T bar: use screw M3*9; Fasten one screw M4*25. 2) Silhouette’ 1/4 and 1/8 XL T bar: use screw M3*6. Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved.
- Page 9 Step 6: Fasten one M3*9 screw to fix device and mounting kit. Before slide the device Slide device by arrow direction to hold on M3*9 screw mounting kit. Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved.
-
Page 10: Install On A Wall
Hole depth: 40.00mm Step 3: Insert the four expansion screws into holes. Only the mounting kit will be used for wall mounting Wall Expansion screw Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved. - Page 11 35kgf/cm Fasten screw M3*9. Slide the device down until the spring hook on the mounting kit meets the groove of the device Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved.
-
Page 12: Powering The Access Point
Powering the Access Point The Celona AP 20 can be powered by IEEE 802.11bt (POE++) on the WAN Ethernet port or connected to an AC electrical outlet using the optional AC power injector/adapter. Access Point Discovery and Provisioning The AP will connect to the Celona Orchestrator for provisioning and discover the Celona Edge within the network on-premises or in the private/public cloud based on the site assignment. -
Page 13: Solution Architecture
Point (AP), which is based on the Qualcomm platform. The AP hosts functions to directs the Celona AP 20 to the serving Celona Edge. provide the following services: Each Celona AP 20 obtains service via its serving Celona Edge. The Celona Edge • Resource management with admission and flow control registers the Celona AP 20, arbitrates spectrum with a FCC approved Spectrum •... -
Page 14: Security
Mobile stations can access data, video, and voice applications over the enterprise performance monitoring and fault monitoring occur over the NETCONF interface. IP network via the Celona Edge after the Celona AP 20 has its radio enabled. Note Celona AP 20’s performance is monitored between every 5 minutes and 15 minutes that the Celona AP 20 can provide voice, video, and data sessions simultaneously based on the periodicity determined by the Celona Edge. -
Page 15: Radio Access Technology
Frequency Band Support (SKUs) Transmit power AP20-48 3.55-3.7 GHz The Celona AP 20 can transmit at a maximum power of 24 dBm max per port, plus Seamless session mobility a built-in omni with max 6 dBi antenna gain. If there are multiple Celona AP 20s in the system all connecting to the same Celona Supported system bandwidth Edge, the Celona AP 20 s can enable seamless mobility for mobile stations. -
Page 16: Contacting Support
Troubleshooting System LED is not blue: • Ensure the AP 20 has a POE++ (802.11bt) connection. POE (802.11 at) is not sufficient. • Please check for loose connections between the POE++ injector / POE++ switch and the Celona AP 20. - Page 17 900 E Hamilton Ave Suite 200, celona.io Campbell, CA 95008, United States © Copyright 2023 Celona Inc. All rights reserved. Installation Guide Celona Indoor Access Point AP 20 © Copyright 2023 Celona Inc. All rights reserved.