EINHELL TE-MS 18/8 Li Original Operating Instructions page 24

All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED flashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove
the battery from the equipment, keep it at room
temperature for one day. If the fault reoccurs, this
means that the rechargeable battery has under-
gone exhaustive discharge and is defective. Re-
move the battery from the equipment. Never use
or charge a defective battery.
6.3 Adjusting the movable stop rail
(Fig. 13 - 16)
Warning! To make 90° crosscuts, the adjustable
stop rail (24) must be fi xed at the inner position:
•
Undo the locking grip for the adjustable stop
rail (19) and push the adjustable stop rail
inwards.
•
The adjustable stop rail (24) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (24) and
the saw blade (5) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking grip (19) again.
Warning! To make 0°-45° miter cuts (with the ma-
chine head (4)inclined or the turntable set at an
angle), the adjustable stop rail (24) must be fi xed
at an outer position.
•
Undo the locking grip for the adjustable stop
rail (19) and push the adjustable stop rail
outwards.
•
The adjustable stop rail (24) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (24) and
the saw blade (5) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking grip (19) again.
6.4 Crosscut 90° and turntable 0° (Fig. 13)
•
Place the piece of wood to be cut at the stop
rail (7 and 24) and on the turntable (8).
•
Lock the material with the clamping device
Anl_TE-MS_18-8_Li_SPK13.indb 24 Anl_TE-MS_18-8_Li_SPK13.indb 24
GB
(22) on the fixed saw table (9) to prevent the
material from moving during the cutting ope-
ration.
•
To turn the saw on, press the release button
(1) and the On/Off switch (3).
•
When you have switched on the saw, wait
until the saw blade (5) has reached maximum
speed.
•
Use the handle (2) to apply steady and light
downward pressure to the machine head (4)
to move it down and cut all the way through
the workpiece.
•
When the cutting operation is completed,
move the machine head back to its upper
(home) position and release the On/Off
switch (3).
•
Warning! The integral resetting springs will
automatically lift the machine head. Do not
simply let go of the handle (2) after cutting,
but allow the machine head to rise slowly, ap-
plying slight counterpressure as it does so.
6.5 Crosscut 90° and turntable 0°- 45°
(Fig. 14)
The crosscut saw can be used to make right and
left angular cuts of 0°- 45° in relation to the stop
rail.
•
Move the machine head (4) to its upper po-
sition.
•
Release the turntable (8) by slackening the
locking grip (10).
•
Set the turntable (8) to the required angle
using the handle (2).
•
Retighten the locking grip (10) to secure the
turntable (8) in place.
•
Cut as described in section 6.4.
6.6 Miter cut 0°- 45° and turntable 0° (Fig. 15)
The crosscut saw can be used to make miter cuts
of 0° - 45° in relation to the work face.
•
Move the machine head (4) to its upper po-
sition.
•
Fasten the turntable (8) in 0° position.
•
Release the clamping lever (12) and use the
handle (2) to tilt the machine head (4) to the
left until the pointer (11) coincides with the
required angular setting on the scale (15).
•
Retighten the clamping lever (12) and make
the cut as described in section 6.4.
6.7 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 16)
The crosscut saw can be used to make miter cuts
to the left of 0°- 45° in relation to the work face
and, at the same time, 0° - 45° in relation to the
- 24 -
18.10.2023 13:08:27 18.10.2023 13:08:27