Table of Contents
Advertisement
MEMORY DIALING
(SPEED DIALING):
MEMORY DIALING
MEMORY DIALING
PRESS
PRESS
PHONE
PRESS
PRESS
YOU WILL SEE
YOU WILL SEE
ENTER MEMORY
ENTER MEMORY
LOCATION (01-20)
LOCATION (01-20)
•
Press the PHONE key.
•
Press MEM .
•
Enter the memory location of the
phone number you wish to dial
(01...20). The number will be
displayed on the LCD and will be
dialed.
CID - CALLER ID
•
To view information stored in CID
memory, press
CID
on the
handset.
CID - CALLER ID
PRESS
YOU WILL SEE
•
The display will show the most
recent call received.
•
To view the time and date of the
call press and hold the 7
key.
The time and date will be shown
along with the phone number.
You will see something like:
As long as the key is held down.
•
To view other calls, scroll
backwards and forwards by using
the
( ) and
(#) keys.
*
•
To view additional dlgits not
shown on the display, press
the
(9) key
•
To exit press OFF .
USING REDIAL
•
Press the PHONE key, then
REDIAL
to automatically redial
out the last number you dialed.
Or
•
Press
REDIAL
so that the
number is shown on the display
and then press the PHONE key.
HOLD
•
Press HOLD
to put a call on
hold.
•
To return to the call, press HOLD
key again
20
MAKING CALLS
You can make calls directly from the
handset whether you are at the base
or away from it.
NOTE: There are two different
ways to dial a number:
1. Press the
PHONE
key and
wait for dial tone. Then dial the
number you want.
Or
2. Enter the number onto the
display first, then press the
PHONE key. This will dial the
number that is displayed on the
LCD after 2 seconds. See
"ADVANCED DIALING" on Page
24
If you make a mistake when dialing,
press OFF to hang up, then press
the PHONE key to get the dial tone
again.
DISCONNECTING
To end a call, either place the
handset back in the base, or press
OFF
on the handset.
ANSWERING CALLS
When the Handset rings, press any
key other than OFF, MUTE or the
VOLUME keys to answer your call.
VOLUME CONTROLS
The volume controls for the handset
are located on the side of the unit.
Press the
(up) or
(down) keys
to increase or decrease the volume.
Holding either key down will
continuously change the volume
setting. The earpiece volume level
indicator on the LCD will change
accordingly. There are four volume
levels.
21
FLASH
You can use your VTech VT 1922
cordless phone with services such as
Call Waiting. Simply press the PHONE
key to FLASH the line.
REDIAL
To REDIAL the last number you
dialed, press the PHONE key, then
press REDIAL . The phone will
automatically dial the number. The
number will be shown on the display.
CLEARING THE DISPLAY
The display can be cleared by pressing
and holding the CLEAR/DEL key
down until the display clears.
MUTE
•
Press MUTE during conversation
to disable the handset micro-
phone.
•
Press MUTE again to return to
normal operation.
RINGER MUTE
•
Press
MUTE
during incoming
ringing to disable the ringer for the
duration of the call.
HOLD
•
Press HOLD to place an active
call on hold.
•
The LCD will display CALL ON
HOLD.
• Press HOLD again to return to the
call.
PAGE/HANDSET LOCATOR
• To page from the Base Unit, press
PAGE .
• The LCD will display BASE PAGING
HANDSET.
•
To
cancel
the
page,
either
press
PAGE again on the Base
Unit, or press OFF on the Handset.
Advertisement
Table of Contents
