Subscribe to Our Youtube Channel
Related Manuals for Exodraft ESP-25
Summary of Contents for Exodraft ESP-25
- Page 1 Electrostatic Particle Filter ESP-25 | Read and save these instructions! Your energy. Optimized.
-
Page 3: Table Of Contents
Your energy. Optimized. Particle Filter | ESP-25 Content Product description Scope of supply Accessories and spare parts Functionality of the electrostatic precipitator Automatic on/off Warranty Technical specifications Precautions and user instructions Mechanical installation Positioning of the ESP-25 Before installation in a chimney construction... - Page 4 How to use this manual This manual has been prepared based on the specific product and contains relevant technical information and installations guides. Accessories and spare parts are not covered by this manual. Please refer to the individual manuals of these components. This installation manual does not contain any system design documentation.
- Page 5 Symbols The following symbols may be used in the manual to draw attention to danger or risk of personal injury or damage to the product. General prohibition Failure to observe instructions marked with the prohibited symbol may result in extreme danger or serious personal injury. General attention Marks a dangerous situation that, in the worst-case scenario, can cause serious personal injury or significant damage to the product.
- Page 6 Touching the electrode or the electrode holder may be fatal. • Exodraft always recommends the use of a smoke alarm when a solid fuel fireplace is installed. • If the Exodraft fan system has been designed for solid fuel/multi fuel installations, please ensure that the design meets the requirements of BS EN15287-1.
-
Page 7: Product Description
Product description The ESP-25 is an electrostatic precipitator (particle filter) for pellet boilers for inline installation in indoor chimney constructions and is placed directly after the pellet boiler. The ESP-25 is designed to reduce the level of particles from pellet boilers. -
Page 8: Functionality Of The Electrostatic Precipitator
Automatic on/off It is possible to connect the ESP-25 to the pellet boiler so that it receives an automatic start/stop signal and standby mode if there is an available and suitable electrical output on the pellet boiler that switches on and off with the boiler. -
Page 9: Warranty
3112024_ESP-25_UK Warranty All Exodraft products are covered by a 2-year guarantee as per European consumer rights legislation. For some countries an extended period of guarantee may apply depending on either national legislation or other clearly stipulated conditions. Customer complaints must be handled by a specialised dealer or wholesaler (preferably where the Exodraft product has been bought originally). -
Page 10: Technical Specifications
High Voltage consumption consumption [kV/mA]* in use [W] standby [W] ESP-25 1 x 115 - 230 50 - 60 20 - 50 30 / 1.7 *Power consumption at min. ambient temperature of -20°C and max. ambient temperature of 35°C. Weight... - Page 11 3112024_ESP-25_UK Construction and components Upper lid Controller Lower lid Main Switch Insulator Inlet for smoke Electrode Outlet for smoke UK | 11...
-
Page 12: Precautions And User Instructions
System type The ESP-25 is only intended for installation in combination with non-condensing pellet boilers with a maxi- mum heating output of no more than 25 kW and can only be used on chimney constructions with negative pressure. -
Page 13: Mechanical Installation
Installation of the ESP-25 must be done in consultation with your chimney sweeper. As the ESP-25 is installed as part of a pellet boiler system, the user must ensure that the design meets the relevant requirements of the country/region. -
Page 14: Before Installation In A Chimney Construction
Before installation in a chimney construction Before installation of the ESP-25, it must be ensured that the electrode is in the correct position. If the elec- trode is out of its correct position, the electrostatic precipitator will not function correctly. - Page 15 The supplied brush stop must be used in installations where the chimney sweeper cleans the chimney from the roof and does not have access to the ESP-25 in the boiler room. The brush stop can be installed from the top. The brush stop is intended to prevent the chimney sweeper from impacting the electrode when cleaning the chimney from the roof.
-
Page 16: Installation In A Chimney Construction
ESP-25 and later deposited after the cleaning process. It is recommended that the viewing angle of the ESP-25 LED is visible from the operating side of the pellet boiler. Insulated or... - Page 17 3112024_ESP-25_UK Attach the warning signs The chimney sweeper must be made aware that the chimney is fitted with an ESP-25 filter. The included high voltage warning signs must be placed on all inspection/cleaning hatches in the chimney system. Connect the ESP-25 to power Connect the ESP-25 power cable to the electrical socket or directly to the boiler.
-
Page 18: Controller
Your energy. Optimized. Controller The illustration and table below shows an overview of the inputs and outputs of the controller. Controller Supply input/output Not used Not used LED diode Not used Not used 1 x 230 V 18 | UK... -
Page 19: Electrical Installation
Power connection by automatic on/off - option 1 ESP-25 can be connected to the pellet boilers main board and be configured to start and stop with the pel- let boiler if it has an available 230 V output. The 5 metre long cable with stripped conductors must then be routed to the pellet boilers outlet according to the electrical diagram. - Page 20 ESP-25 can be connected to the boiler through a relay setup (control box start / stop). In this way, ESP-25 can be connected to all available 24-230V outputs on the pellet boiler.
-
Page 21: Start-Up And Configuration
System test When the ESP-25 is activated for the first time, the chimney must be cold. Check that the LED lights up green after approx. 10 seconds. There may be a very slight buzzing sound when the filter starts, this is normal. -
Page 22: User Operation Instructions
NOTE! Be aware that even if the ESP-25 fails, the pellet boiler may still be in operation. In the event of a power failure (and the ESP-25 is not supplied with power), air and smoke will be able to pass freely through the flue, meaning that the pellet boiler is still safe to use. -
Page 23: Indications On The Esp-25
3112024_ESP-25_UK Indications on the ESP-25 The LED is located at the lower lid of the ESP-25 and indicates the current status. The following diagram illustrates the various status categories, as indicated by the LED. No light - OFF Green - ON... -
Page 24: Maintenance And Troubleshooting
Ensure that the pellet boiler and the ESP-25 cannot be turned on accidentally. Do not open any part of the ESP-25 filter unless the power supply is turned off via the power switch and the plug has been removed from the electrical socket. -
Page 25: User Maintenance
NOTE! It is the user’s responsibility to inform the chimney sweeper that an ESP-25 has been installed, so that the chimney sweeper is aware of this before cleaning the chimney. If the chimney sweeper is to clean from the boiler room (cleaning the chimney from below and below the ESP-25), the user must introduce the chimney sweeper to the proce- dure in the manual. -
Page 26: Inspection And Service
Your energy. Optimized. Inspection and service DANGER! Make sure that the ESP-25 is switched off, unplugged from the socket and that the pellet boiler is turned off during cleaning, inspection and servicing. During inspection and service remove the lids for access to the insulator and technical compartments and check the following. - Page 27 Replacing spare parts Apart from replacing the electrode in case of damage, no other repairs to the ESP-25 are allowed by user without first seeking advise. In case of defects, please contact your Exodraft dealer.
-
Page 28: Cleaning Procedure - Performed By User
Action The boiler must be switched off. Wait for the chimney to cool down. The main switch of the ESP-25 must be switched off, and the supply cable must be unplugged from the electrical socket (if not powered by the boiler). -
Page 29: Chimney Sweeping - Performed By Chimney Sweeper
Action The boiler must be switched off. Wait for the chimney to cool down. The main switch of the ESP-25 must be switched off, and the supply cable must be unplugged from the electrical socket (if not powered by the boiler). -
Page 30: Troubleshooting
Your energy. Optimized. Troubleshooting Troubleshooting when warning lights are on. Please refer to section Indications on the ESP-25. Observation Problem Solution LED constant red General failure Call for service Connect the power supply to a grounded Flashing red LED Poor or no PE connection... -
Page 31: Uk Conformity Assessed
UK Conformity Assessed UK Conformity Assessed Exodraft a/s Industrivej 10 DK-5550 Langeskov Hereby declares that the following products: ESP-25 Were manufactured in conformity with the provisions of the following regulations: The Supply of Machinery (Safety) Regulations 2008 Electrical Equipment (Safety) Regulations 2016... -
Page 32: Declaration Of Conformity
EU-Vaatimustenmukaisuusvakuutus Déclaration de conformité de l’Union Européenne ESS-Samræmisstaðfesting EU-Samsvarserklæring Dichiarazione di Conformità Unione Europea EU Deklaracja zgodności Exodraft a/s Industrivej 10 DK-5550 Langeskov Erklærer på eget ansvar, at følgende produkter: Veklaart dat onderstaande producten: Hereby declares that the following products: Deklarerar på... - Page 36 DK: Exodraft a/s Industrivej 10 DK-5550 Langeskov Tel: +45 7010 2234 Fax: +45 7010 2235 info@exodraft.dk www.exodraft.dk SE: Exodraft a/s Kalendevägen 2 SE-302 39 Halmstad Tel: +46 (0)8-5000 1520 info@exodraft.se www.exodraft.se NO: Exodraft a/s Storgaten 88 NO-3060 Svelvik Tel: +47 3329 7062 info@exodraft.no...
Need help?
Do you have a question about the ESP-25 and is the answer not in the manual?
Questions and answers