Subscribe to Our Youtube Channel
Related Manuals for Bilt STEPR
Summary of Contents for Bilt STEPR
- Page 1 STAIR CLIMBER USER MANUAL Scan for easy 3D instructions Tap. Zoom. Rotate with official interactive instructions on the BILT app.
- Page 2 WARNINGS AND SAFETY INFORMATION ASSEMBLY MOVING THE STEPR GROUNDING METHODS APP ONBOARDING PROCESS PROPER USAGE CLASS SCREEN CARE AND MAINTENANCE EXPLODED DRAWING PARTS LIST...
- Page 3 Do not use any attachments that are not recommended by the manufacturer. Do not operate the STEPR if the cord or plug is damaged, if it is not functioning correctly, if it has been dropped or damaged, or if it has fallen into water.
- Page 4 IMPORTANT SAFETY INSTRUCTION! the STEPR is designed for indoor use only. Do not use it outdoors. Avoid operating the STEPR in areas where aerosol (spray) products are being used or where oxygen is being administered, as it may pose a safety risk.
- Page 5 Never operate the STEPR if the cord or plug is damaged, if it is not functioning correctly, if it has been damaged, or if it has been immersed in water. Operating the STEPR under such conditions may lead to safety hazards.
- Page 6 The STEPR is intended for adult use only and should be used indoors. Provide adequate care, guidance, and supervision for older adults, children, and individuals with disabilities using the STEPR. Do not plug any other devices into the STEPR, as it may cause damage or electrical hazards.
- Page 7 Always turn Screen prior to moving the STEPR Always cut off the power supply when the STEPR is not in use. When turning off the power, avoid pulling the power line to keep it from breaking.
-
Page 8: Important Safety Precaution
Always wear athletic shoes while using this STEPR to ensure proper foot support and stability. Refrain from jumping on the STEPR, as it may lead to damage or injuries. Only one person should be on the STEPR while it operation prevent accidents interference with its function. - Page 9 In such cases, discontinue use and have it inspected by a qualified professional. Keep the power cord away from heated surfaces to avoid damage and potential hazards. Do not carry the STEPR by its supply cord or use the cord as a handle.
- Page 10 To disconnect the STEPR, turn the power switch to the off position, and then remove the plug from the electrical outlet. Do not use the STEPR in locations that are not temperature-controlled, such garages, porches, pool rooms, bathrooms, carports, or outdoors.
- Page 11 For the safety, stability, and optimal performance of your STEPR, it is imperative to use only light and ultra-light bands on all upright anchor points and in all rear anchor points. Utilizing heavy bands or...
- Page 12 assembly & installation Easy to follow with voice, text & interactive 3D images DRAG TO ROTATE • Faster than paper or video Audio, text & • image prompts TAP FOR DETAILS Rotate & zoom • 3D images 360° • Replay steps instantly PINCH TO ZOOM •...
-
Page 13: Assembly Steps
ASSEMBLY STEPS Note: The floor area of this STEPR is 45.6x28.7in (115.8x71.9cm) Product Net Weigth: 297.62lbs (135kgs) Note: At least 2 persons are required to assemble the STEPR. STEP 1 Open the package, take out all parts and unwrap carefully with special attention to the Console. - Page 14 STEP 2 Pass the Emergency Switch Upper Wire 2 (123) on the Right Upright Tube (2R) through the right Decorative Cover (49R) to connect with the Emergency Switch Lower Wire 2 (124) on the right of the Main Frame (1). Insert the right Upright Tube (2R) through the right Decorative Cover (49R), then slide the Upright Tube onto Right lower tubes on the Main Frame (1) and...
- Page 15 STEP 3 Connect the Console Lower Extension Wire (119) to the Console Lower Wire (120). Attach the Lower Console Mast (5) to Main Frame (1) with four M10*30 Hex socket screws (73) and four 1 0 flat washers (105). (Please don’t tighten them ∅...
- Page 16 STEP 4 Hold the Console (132) carefully and align the position with Mounting Plate (6), then lock the Console to Mounting Plate with four M10*20 Hex socket screws (74) and four 1 0 Lock washers (102) ∅ securely. Insert the Keyboard Extension Wire (128), Console Upper Extension Wire (118), Emergency Switch Lower Wire 1(122) and Pulse Upper wire (125) into the corresponding color/size sockets of the Socket...
- Page 17 STEP 5 Connect the Console Upper Extension Wire (118) to the Console Lower Extension Wire (119) . Attach the Upper Console Mast (4) to the Lower Console Mast (5) with four M10*20 Hex socket screws (74) and four 1 0 Lock washers (102). ∅...
- Page 18 STEP 6 Pass the Key Board Lower Wire (129a) on left Handrail (3L) through the open D and out of hole C on right Handrail (3R), then insert the left Handrail (3L) into the right Handrail (3R). (Please be careful not to clip the wires ).
- Page 19 Insert the G tube of the Handrail Set (3L/R) into the Upright Tubes (2L/2R), align the holes and lock with six M10*20 Hex socket screws (74) and six 1 0 Lock ∅ Washers (102). (Please don’t tighten them now) Align the 4 holes around the bottom connection of Handrail Set (3L/R) with the connection tube of the Upper Console Mast (4), and lock with four M8*20 Hex bolts (77) and four...
- Page 20 STEP 8 Lock all the sixteen M10*20 Hex socket screws (74) and the four M10*30 Hex socket screws (73) that are not locked tightly in previous assembly steps. Clip the Decorative Cover (49L/49R) into the Protective Cover (44L/44R) respectively and press to ensure they are clipped properly.
- Page 21 STEP 9 Put the Exterior Decorative Cover (41L/41R) onto the outside of Handrail (3L/R) and Upright Tube (2L/R) joint; Put the Interior Decorative Cover (42L/42R) from the other side and lock them together with two ST4*16 Cross tapping screws (89) respectively.
- Page 22 STEP 10 Lock the Bottle/Phone Holder (40) to the Lower Console Mast (5) with two M6*25 Hex head screws (79). Stretch gently the soft Console Mast Decorative Cover (55) with hands and then put it around the joint of Lower Console Mast (5) and the Main Frame (1).
- Page 23 Handles (138) from the Main Frame (1). Store the Transport Handles in a safe place for future use. Make sure the STEPR is steady on the floor, level the STEPR by adjusting the 4 feet (59). Tighten the feet with 17 open wrench...
- Page 24 MOVING THE STEPR Remember, not following these instructions could result in injury. Always prioritize safety and ensure that these instructions are followed precisely. If you are unsure or uncomfortable with moving the machine, please seek professional assistance.
-
Page 25: Grounding Methods
STEPR is properly grounded. Do not modify the plug provided with the STEPR – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. - Page 26 APP ONBOARDING PROCESS STEP 1 STEP 1 Plug in your STEPR to a power source using the provided power adapter. Turn on the console using the power button located on the rear bottom of the STEPR. Follow the on-screen instructions to connect STEPR to your Wi-Fi network.
- Page 27 STEP 4 Choose Your STEPR Plan. Browse through the available plans and select the one that best suits your fitness goals and preferences. Follow the prompts to subscribe to your chosen plan.
-
Page 28: Proper Usage
STEPR to a smooth stop. After the machine has come to a complete stop, the user can safely exit the step area of the STEPR in the direction indicated by the arrow. - Page 29 If you experience excessive shaking of the stairs during exercise, it may indicate that the chain is too loose. Follow the steps below to adjust the chain tension, or reach out to support@getstepr.com Remove the left and right protective covers of the main frame.
- Page 30 If the start/stop button is damaged during use, you cannot continue to use the STEPR, and you need to replace the internal electronic parts before you continue to use the machine The surface of stairs are plastic, which is easy to wear and tear.
- Page 31 Dismounting the STEPR - After the steps have come to a complete stop and while grasping the handlebars, step down onto the floor. FREQUENT ERRORS emergency stop switch been activated. Rotate the emergency stop switch clockwise to release. The infrared sensor detects an obstacle. Clear...
- Page 32 |f thie STEPR does cause harmful interference to radio or television reception,which can be determined by turning the STEPR off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
-
Page 35: Care And Maintenance
Do not use the STEPR until the defective components have been replaced or repaired by a qualified professional. Keep the STEPR Out of Use Until Repair: In the event damage significant... -
Page 36: Exploded Drawing
EXPLODED DRAWING... -
Page 37: Parts List
PARTS LIST... - Page 38 PARTS LIST...
- Page 39 © STEPR 2023, | STEPR, INC. All rights reserved. getstepr.com...
Need help?
Do you have a question about the STEPR and is the answer not in the manual?
Questions and answers