SECTION 4 TEST MODE [LED All Lit, Key Check Mode] Procedure: 1. Press the button to turn the power ON. 2. Press three buttons of (DECK B), (DISC 1), and [DISC 5] simultaneously. 3. LEDs are all turned on. Press the (CD) button, and the key check mode is activated.
SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution TAPE DECK SECTION 0 dB=0.775 V 1. Clean the following parts with a denatured alcohol-moistened swab: 1. Demagnetize the record/playback head with a head demagne- record/playback heads pinch rollers tizer. erase head rubber belts 2.
Page 5
DECK B 2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak. • Execute only if connected to the STR-NX1/NX3 Mode: Playback test tape AUDIO OUT jack...
Page 6
DECK B REC Bias Adjustment Specified value: AUDIO OUT jack PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB) Procedure: 1. Mode: Record Adjustment Location: MAIN board AUDIO IN jack – MAIN BOARD (Conductor Side) – 1) 315 Hz ...
RF LEVEL CHECK CD SECTION Note: oscilloscope 1. CD Block is basically designed to operate without adjustment. There- fore, check each item in order given. BD board 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10 MΩ impedance. TP (RF) 4.
Page 8
HTC-NX1 7-3. SCHEMATIC DIAGRAM – BD Board – • See page 32 for Waveforms. • See page 32 for IC Block Diagrams. (Page 29) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety.
Page 9
HTC-NX1 • Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY 7-5. SCHEMATIC DIAGRAM – CD MOTOR/SENSOR Section – • See page 33 for IC Block Diagram. (Page 29) (Page 29)
Page 10
HTC-NX1 7-7. SCHEMATIC DIAGRAM – AUDIO Board – • See page 33 for IC Block Diagram. PB EQ AMP (PLAYBACK) (DECK A) PB LEVEL (L) (DECK A) PB LEVEL (R) (DECK A) PB EQ AMP (DECK B) PB LEVEL (L) (DECK B) A +7.5V PB LEVEL (R)
Page 11
HTC-NX1 7-8. PRINTED WIRING BOARD – LEAF SW Board – • See page 19 for Circuit Boards Location. DECK B DECK A PLUNGER PLUNGER (DECK B PLAY) (DECK B 120/70) (DECK A PLAY) (DECK B HALF) (DECK A REC) (DECK A 120/70) (DECK A HALF) (Page 27) 7-9.
Page 12
HTC-NX1 7-11. SCHEMATIC DIAGRAM – MAIN Board (1/2) – (Page 25) (Page 26) (Page 29) • Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont ) : TAPE PLAYBACK (DECK A) line with mark 0 are critical for safety.
Page 13
HTC-NX1 7-12. SCHEMATIC DIAGRAM – MAIN Board (2/2) – • See page 32 for Waveform. (Page 28) (Page 31) (Page 23) (Page 23) (Page 31) (Page 31) (Page 21) • Voltages and waveforms are dc with respect to ground ] : TAPE PLAYBACK (DECK B) 〈〈...
Page 14
HTC-NX1 7-14. SCHEMATIC DIAGRAM – PANEL Section – (Page 29) (Page 29) (Page 29) • Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY...
(3) CD MECHANISM DECK SECTION-1 (CDM53D-K1BD33) M702 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-218-253-01 SCREW (M2.6), +BVTP 4-214-129-01 COVER * 152 1-671-508-21 LOAD MOTOR BOARD 4-211-235-01 BELT (COMMUNICATION) 4-220-261-01 GEAR (EJECT) 4-211-236-01 BELT (LOADING) * 154 1-671-502-21 INT/COUNT SW BOARD 4-220-278-01 PULLEY (MODE)
Page 16
(4) CD MECHANISM DECK SECTION-2 (CDM53D-K1BD33) not supplied not supplied S707 not supplied M701 BU-K1BD33 supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 4-220-275-01 GEAR (CHUCKING) 4-220-933-01 INSULATOR 4-211-245-01 SPRING, COMPRESSION 4-213-487-53 TRAY (SUB) * 226 1-671-507-21 CLAMP MOTOR BOARD...
Page 17
(5) CD BASE UNIT SECTION (BU-K1BD33) not supplied not supplied not supplied M101 M102 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
Page 20
SECTION 9 AUDIO ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
Page 29
SECTION 4 TEST MODE [CD Delivery Mode] 5. To release from these mode, press three buttons in the same • Execute only if connected to the HTC-NX1. manner as step 2, or remove the power cord. • This mode moves the optical pick-up to the position durable to [MC Hot Reset] vibration.
Page 30
[Aging Mode] • Display at an error occurred • Execute only if connected to the HTC-NX1. 1) Display of the error count [ENTER] [POWER SAVE/DEMO] This mode can be used for operation check of CD section and tape (1) Press three buttons of [GROOVE] deck section.
Page 31
3. Tape Deck Section • The sequence during the aging mode is following as below. • If an error occurred, stop display that step. Aging mode sequence (Tape deck section) : Rewind the tape A and B “TAPE A AG-1” Shut off FWD play the tape A “TAPE A AG-2”...
Page 35
STR-NX1/NX3 5-7. SCHEMATIC DIAGRAM – SURROUND AMP Board – (NX3) (Page 12) (Page 19) The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
Page 36
STR-NX1/NX3 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 5-9.
Page 38
STR-NX1/NX3 5-13. SCHEMATIC DIAGRAM – TRANSFORMER Section – (Page 19) (Page 14) (Page 13) (Page 14) The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
Page 39
SECTION 7 BACK LIGHT MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark are seldom required for routine service. parts list may be different from the parts speci- 0 are critical for safety.