Download Print this page

Sony ILCA-77M2 Service Manual page 29

Interchangeable lens digital camera
Hide thumbs Also See for ILCA-77M2:

Advertisement

2-1-10. IMAGER SECTION
ns: not supplied
Anti Shake Unit Section
(See page 2-14)
(including HOL-007 flexible board)
451
453
463
(Note 1, 2, 3)
454
(Note 1)
Note 1: Refer to "3-2. CLEANING PROCEDURE OF OLPF" on
page 3-2 for method of cleaning the OLPF.
Note 2:
Precautions for Replacement of Imager
• 
If the imager has been replaced, carry out all the adjustments for the
camera section.
• 
As the imager may be damaged by static electricity from its structure,
handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts nor
 
exposed to strong light.
Ref. No.
Part No.
Description
451
4-194-226-01
IM PLATE, LPF RETAINER
452
A-2042-734-A
IM IMAGER UNIT ASSY (880) (Note 1, 2)
453
4-534-930-01
IM MASK PLATE (880)
454
4-281-915-01
IM GS TAPE (Note 1)
455
4-185-993-02
IM SHEET, SPACER (Note 1)
456
1-884-796-21
ISP-004 FLEXIBLE BOARD
457
1-884-795-21
ISL-005 FLEXIBLE BOARD
458
4-421-277-01
IM SHEET, RADIATION (874)
ILCA-77M2/77M2M/77M2Q_L2
452
(including CP6001 (CMOS imager) and
IS-095 complete board)
(Note 1, 2)
ns
458
455
(Note 1)
454
(Note 1)
460
461
457
456
Note 1:  OLPFの清掃方法は3-2ページの "3-2. CLEANING PROCE-
DURE OF OLPF" を参照してください。
Note 2:
イメージャ交換時の注意
・   イメージャを交換した場合は,カメラ部の全調整を行ってくださ
い。
・   イメージャは構造上,静電気により破壊される恐れがあるため,
MOS ICと同様に注意して取り扱ってください。
  また,受光部にはゴミの付着,および強い光がはいることのない
ように注意してください。
Ref. No.
Part No.
Description
459
4-421-276-01
IM HEAT SINK (874)
460
4-194-225-01
IM TAPE FPC GUIDE
* 461
4-194-227-01
IM PLATE GUIDE IMAGER FPC
462
4-295-215-01
IM SHEET GRAPHITE 870
463
A-2059-919-A
OPTICAL FILTER BLOCK (SERVICE) (Note 1, 2, 3)
#64
2-666-551-21
SCREW, TAPPING, P2
Screw
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
1.7
5.0
Note
Note 3 :
Refer to the following statements when replacing the Optical
filter block.
Method of Removal
(1) Pour resolvent (alcohol or cleaning agent) between the
imager and the IM spacer.
* Wait for that the adhesive power of the IM spacer
weakens.
(2) Remove the IM spacer from the imager.
459
Method of Attachment
#64
(1) Attach the two IM GS tapes and the Optical filter block
by aligning them with the outer shape of the IM
spacer evenly.
* Confirm the mounting direction of the Optical filter
block referring to "3-1. ASSEMBLY".
#64
Peel off the
release paper
462
Optical Filter Block
(2) Set the Optical filter block in its attachment jig
(J-6082-737-A), with the attached adhesive face of IM
spacer facing upward.
(3) Press the imager down into the jig as shown below to
attach it to the Optical filter block.
Imager
J-6082-737-A
2-13
Note 3 :
光学フィルタブロックを交換する際は,下記を参照してくだ
さい。
取り外し方
(1) イメージャとIM間隔板の間に溶剤(アルコールまたはク
    リーニング液)を流し込む。
    * IM間隔板の粘着力が弱くなるのを待ってください。
(2) イメージャからIM間隔板を取り外す。
Pour resolvent (alcohol or
cleaning agent) between
the imager and the IM spacer.
組み付け方
(1) IM間隔板に対し,上下左右が均一になるように
    IM GS TAPE2枚および光学フィルタブロックを貼り
    付ける。
    * "3-1. ASSEMBLY"を参照し,光学フィルタブロックの
   取り付ける向きを確認してください。
Peel off the
Peel off the
release paper
release paper
Peel off the
release paper
IM GS Tape
IM Spacer
IM GS Tape
光学フィルタブロック
(2) IM GS TAPEの粘着面が上になるように,光学フィルタブロッ
    ク貼付け治具(J‑6082‑737‑A)にセットする。
(3) イメージャを図のように治具に押え付け,光学フィルタブ
    ロックに貼り付ける。
イメージャ
Peel off the release paper.
J-6082-737-A
イメージャとIM間隔板の間に溶剤
(アルコールまたはクリーニング液)
を流し込む。
剥離紙を剥がす
剥離紙を剥がす
剥離紙を剥がす
剥離紙を剥がす
IM GS TAPE
IM間隔板
IM GS TAPE
剥離紙を剥がす

Advertisement

loading

This manual is also suitable for:

Ilca-77m2mIlca-77m2q