Advertisement
Zl
Before plugging the AX-V4BK into an AC outlet, make sure that all connections have been made.
When the power cord is connected, the STANDBY indicator above the POWER button lights up.
Keep the power cord away from the connecting cables for the TV, VCR, and antenna. The power cord may
cause noise or screen interference.
Notes:
+ Asmall amount of power is always consumed even in standby mode. To switch off the power completely,
unplug the power cord from the AC outlet.
+ Ifthe power cord is unplugged or a power failure occurs, preset settings will be erased in a few days.
CAUTIONS:
* Do not touch the power cord with wet hands.
* Donotpullonthe power cord to unplug the AX-V4BK. When unptugging the AX-V4BK, always.
grasp the plug itself so as nol to damage the cord.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batterics first. When using the remote contro}, aim the
remote control directly at the remote sensor on the AX-V4BK,
1. On the back of the remote control, press down on the battery cover and slide ft out.
2. Insert batteries. Make sure to observe the proper polarity: (+) to (+) and (-) to (-).
3. Slide the cover tn.
ge
2
AGP (SUM-3)/AA (15F)
4
If the range or effectiveness of the remote contro] decreases, replace the batteries. Use two R6P (SUM-3)/
AA (I5F) type dry-ceil batteries.
CAUTIONS:
Follow these precautions to avoid leaking or cracking cells:
¢ Place batteries in the remote control so they match the polarity indicated: (+) to (+) and (-)
to (-).
+ Use the correct type of batteries. Batteries that look simitar may differ in voltage.
* Always replace both batteries at the same time.
* Do not expose batteries to heat or flame.
Page 9
Basic Operations
The following operations are commonly used when you play any sound source.
Turning the Power On and Off
Se
Totura on the power, press the POWER button on the front panel or the AUDIO button on the remote control.
aL cai
N10
The STANDBY indicatur goes off.
To turn off the power, press the POWER button or AUDIO button on the remote control again.
The STANDBY indicator lights up.
On the front
From the
panel
remote control
Salecting the Source to Play
You nced to select the source to listen before you start playing any source.
Press one of the source selecting buttons so that the source name appears on the display.
Selected source name appears
=
Et
>
5
On the front panel:
i)
ie) 9
ce)
TUNER
Listen to the tuner.
(©) (@)
TAPE
Listen to the cassette deck connected to the TAPE jacks.
PHONO
Listen to a record.
cD
Listen to the CD player.
VIDEO
View the video component connected to the VIDEO jacks.
On the front panel
VCR
View the video component connected to the VCR jacks.
From the remote control:
=)
PHONO*
Listen to a record.
C3
VIDEO
View the video component connected to the VIDEO jacks.
TUNER*
Listen to the tuner.
cD*
Listen to the CD player.
TAPE*
Listen to the cassette deck connected to the TAPE jacks.
©
>
VCR
View the video component connected to the VCR jacks.
TAPE
Note:
* When you press one of the source selecting buttons on the remote control marked above with an asterisk,
the AX-V4BK automatically turns on.
From the remote control
Selecting different sources for picture and sound
You can watch picture from video equipment while listening to sound from audio equipment.
To listen to the sound from audio equipment while watching the picture from video equipment, press
one of the source selecting buttons for the video equipment (TUNER, TAPE, PHONO or CD), then press one
of the source selecting buttons for the audio equipment (VIDEO or VCR).
Page 10
MavA-XV
Advertisement
