Kroks ARINST VR-23-6200 Manual

8. Additional equipment and accessories.
The device initially has a factory calibration entered into non-volatile memory. The relevant information is
displayed in the lower information line of the screen. The calibration plane corresponds to the port (1) of the device,
intended for connecting the devices under test and the load (TEST PORT). To increase measurement accuracy when
using optional adapters and cables, a full one-port calibration must be performed using a set of calibration standards,
purchased separately.
ID. 1817 N-MF06 50 Ohm SOL (Short/Open/Load) Calibration Kit with "N" connectors.
ID. 1795 SMA-MF06 50 Ohm SOL (Short/Open/Load) Calibration Kit with SMA Connectors
A complete guide for setting up, calibrating, taking measurements, operating the device and updating the device
firmware is available on the websites www.arinst.net and www.kroksw.com.
7. Warranty
The manufacturer guarantees that this product meets the specifications specified in this document. The warranty
period is 12 months from the date of purchase. During this period, the manufacturer provides a free warranty service.
The warranty does not cover the following cases:
 the warranty period of the product has expired from the date of sale;
 there are no documents confirming the date and fact of purchase of the product;
 the product intended for personal needs was used for commercial activities, as well as for other purposes
that do not correspond to its intended purpose;
 violations of the rules and operating conditions set out in the Operating instructions and other
documentation provided to the Buyer complete with the product;
 if there are traces of unskilled repairs or attempts to open the Product outside an authorized service center,
as well as due to unauthorized interference with the software;
 damage (deficiencies) of the Goods caused by the impact of virus programs, interference with the software,
or the use of third-party software (non-original);
 the defect is caused by force majeure (for example, an earthquake, fire, lightning strike, instability in the
electrical network), accidents, deliberate or careless actions of the consumer or third parties;
 mechanical damage (cracks, chips, holes) arising after the transfer of the product to the Buyer;
 damage caused by exposure to moisture, high or low temperatures, corrosion, oxidation, ingress of foreign
objects, substances, liquids, insects into the product;
 the defect occurred due to the supply of a signal or voltage or current exceeding the permissible values for
this Product to the input connectors, terminals, housing;
 the defect is caused by natural wear of the Product (for example, but not limited to: natural wear of
connectors due to frequent connection/disconnection of adapters).
Warranty obligations apply only to defects caused by the fault of the manufacturer. Warranty service is performed
by the manufacturer or an authorized service center.
Date of sale____________________Seller________________________________________
(date, month, year)
I have read the instructions and operating rules ____________________________
(store name or stamp)
(Buyer's signature)
1818
Portable vector network analyser
Manual. Passport products.
1. Purpose.
Portable single-port vector network analyzer ARINST VR 23-6200 (Vector Reflectometer) is designed to measure
the matching characteristics of passive and active radio devices
etc.). The device allows you to measure the parameters of the complex reflection coefficient, standing wave ratio
(VSWR), impedance, admittance, phase, loss and distance to a fault in the cable.
The device is intended for amateur radio use, as it is not a professional measuring instrument. The presence of a
built-in battery allows measurements in laboratory and field conditions.
When purchasing a reflectometer, check its completeness. Attention! After purchasing the device, claims for
incompleteness are not accepted!
The devices under test must allow the possibility of applying a stimulating signal from the reflectometer to the port
under test. The reflectometer manufacturer is not responsible for the failure of devices that do not allow a stimulating
signal to be sent to the port under test.
2. Contents of delivery.
Name
Vector network analyser ARINST VR-23-6200
Cable for charging the device battery mini-USB(male) - USB2.0(male)
Manual
Package
3. Device structure.
394005, Voronezh, Moskovsky pr. 133-263
ARINST VR-23-6200
1
(antennas, cables, filters, attenuators, amplifiers,
Qty Due to the constant improvement of
the device and software, the
1
manufacturer reserves the right to
1
make changes to its technical
1
characteristics and completeness.
1
1. Port for connecting devices under test and load TEST
PORT
2. Housing
3. Color resistive screen 3.2"
4. Block of control buttons
5. Connector for data transfer and battery charging device
USB type B
6. Connector for data transfer and battery charging mini-
USB
7. CHARGE battery charging indicator
Kroks Plus LLC
+7 (473) 290-00-99
info@kroks.ru
www.kroks.ru