Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ARRI Hi-5 SUP 2.1
Summary of Contents for ARRI Hi-5 SUP 2.1
- Page 1 Hi-5 SUP 2.1 Software Update Package (SUP) 2.1 RELEASE NOTES December 11, 2023...
-
Page 2: Table Of Contents
Power Issues __________________________________________________________________________________ 11 E. Update Instructions ____________________________________________________________________________ 14 How to get a Software Update Package _____________________________________________________________ 14 Hi-5 Update Procedure via USB ___________________________________________________________________ 14 Hi-5 SUP 2.1 Release Notes Page 2 of 14 All data subject to change without further notice. -
Page 3: Introduction
A. Introduction This document describes changes from Hi-5 SUP 2.0 to Hi-5 SUP 2.1. Those changes and new features are a result of direct feedback from users. This is an important update for the Hi-5 ecosystem and it provides a big improvement in the overall system stability. -
Page 4: New Features With Sup 2.1
In addition, a new user button ‘Favorite Rings’ is introduced as a menu shortcut. This allows you to navigate directly into the favorite ring selection page from the Hi-5 homescreen. Hi-5 SUP 2.1 Release Notes Page 4 of 14 All data subject to change without further notice. -
Page 5: Lens Menu Improvements
Hi-5 Lens menu. The values can now be entered in full stops and fractions of a stop for easier adjustments. When not in use it can be quickly deactivated. Hi-5 SUP 2.1 Release Notes Page 5 of 14... -
Page 6: Virtual Focal Length Improvements
The generated serial will have an appended ‘R’ to be sure the LDA files with a random serial number can be distinguished from a real serial number. Hi-5 SUP 2.1 Release Notes Page 6 of 14 All data subject to change without further notice. -
Page 7: Cinefade License
Cinefade license The Cinefade License Key for Hi-5 is available via the ARRI license shop: https://alshop.arri.de/ Remote control of a Cinefade device via a Hi-5 hand unit when the Cinefade is connected to the RIA-1 LBUS • daisy chain. •... -
Page 8: Bugfixes And Stability Improvements
C. Bugfixes and stability improvements This release contains many bugfixes and stability improvement, including the following: • Playback issues with ARRI cameras have been fixed and handling improved Fixed problems with network mode when 3 RF-EMIP clients are connected •... -
Page 9: Known Issues
This is part of the initialization sequence of the Radio Module and only a visual irritation without further impact. SDI status information can’t be set to “safe” This SDI setting is currently not settable via hand units as it is not transmitted by ALEXA Mini/Mini LF. For ARRI ALEXA models, SDI “safe” does not exist. -
Page 10: Cforce Mini Rf
If the RF-2400 radio modules had been used in an ARRI TRINITY 2 Remote Control Panel RCP-3, they must be reconfigured to be ARRI ECS compatible. This is easily done by attaching them to a Hi-5 and waiting for about 10 seconds. -
Page 11: Focusbug Cine Rt
If a distance measure device is connected to the RIA-1, but no distance value is shown, check if the correct serial mode is set in the RIA-1. Serial Mode > UDM: Use this setting when connected to a ARRI's Ultrasonic Distance Measure (UDM-1) or a CineTape Measure Control. -
Page 12: Cinefade
Legacy ARRI cameras No codec information with legacy cameras There is no codec information with ARRI legacy cameras. This issue can’t be fixed and was apparent also with the WCU-4, as ARRI legacy cameras don’t transmit this information to hand units. -
Page 13: Red Cameras
Workaround: Activate pre-recording via camera or assign a user button on the RED camera to Start/Stop. RED Komodo playback manipulation not possible FFW and FBW in playback mode is not supported by RED Komodo Hi-5 SUP 2.1 Release Notes Page 13 of 14 All data subject to change without further notice. -
Page 14: Update Instructions
(4) Unplug the USB drive from the Hi-5 and connect it to your computer. (5) Copy the Software Update Package file into the folder ARRI/Hi-5/SUP, created on the USB drive. (6) Eject the USB drive from your computer and insert it into the corresponding USB slot of the Hi-5.
Need help?
Do you have a question about the Hi-5 SUP 2.1 and is the answer not in the manual?
Questions and answers