Viking Designer DGRT3004B Installation Instructions Manual
30”, 36” w. and 48” w. dual fuel ranges
Hide thumbs
Also See for Designer DGRT3004B:
- Specification sheet (5 pages) ,
- Specifications (5 pages) ,
- User manual (175 pages)
Table of Contents
Advertisement
Quick Links
INSTALLATION
INSTRUCTIONS
DUAL FUEL RANGES
IMPORTANT - PLEASE READ AND FOLLOW
•Before beginning, please read these instructions completely and carefully.
•Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
•Please observe all local and national codes and ordinances.
•Please ensure that this product is properly grounded.
•The installer should leave these instructions with the consumer who should retain for local inspector's use and for future
reference.
Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSI Z223.1-latest
edition. IN CANADA: Installation must be in accordance with the current CAN/CGA B149.1 & 2 Gas Installation codes
and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes
Part 1 and/or local codes.
In Massachusetts: All gas products must be installed by a "Massachusetts" licensed plumber or gasfitter. A "T" type
handle manual valve must be installed in the gas supply line to the appliance.
Frame grounded to neutral of appliance through a link. If local codes do not permit grounding through the neutral, the
3-conductor cord or cable assembly must be replaced by a 4-conductor cord or cable assembly. See manufacturer's
instructions.
WARNING:
IF THE INFORMATION IN
THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY DAMAGE,
PERSONAL INJURY, OR DEATH.
1. Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
2. WHAT TO DO IF YOU SMELL GAS:
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use any
phone in your building.
•Immediately call your gas supplier from a neighbor's
phone.
•Follow the gas supplier's instructions.
•If you cannot reach your gas supplier, call the fire
department.
3. Installation and service must be performed by a
qualified installer, service agency, or the gas supplier.
WARNING
If not installed, operated and maintained in
accordance with the manufacturer's instructions, this
product could expose you to substances in fuel or
from fuel combustion which can cause death or
serious illness and which are known to cause
cancer, birth defects, or other reproductive harm.
For example, benzene is a chemical which is
part of the gas supplied to the cooking
product. It is consumed in the flame during
combustion. However exposure to a small
amount of benzene is possible if a gas leak
occurs. Formaldehyde and soot are by-
products of incomplete combustion. Properly
adjusted burners with a bluish rather than
yellow flame will minimize incomplete
combustion.
WARNING!
•This range can tip.
•Injury to persons could result.
•Install anti-tip device packed with range.
•See Installation Instructions
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
WARNING
Advertisement
Table of Contents
Related Manuals for Viking Designer DGRT3004B
Summary of Contents for Viking Designer DGRT3004B
-
Page 1: Installation Instructions
•If you cannot reach your gas supplier, call the fire department. 3. Installation and service must be performed by a qualified installer, service agency, or the gas supplier. VIKING RANGE CORPORATION Greenwood, Mississippi 38930 USA WARNING If not installed, operated and maintained in accordance with the manufacturer’s instructions, this... - Page 2 Specifications - Dual Fuel 30”, 36” W. and 48” W. Ranges Description 30” W. Models Overall width 29 7/8” (75.9 cm) Overall height Open Burner To top of grate support - Min. 35 7/8” (91.1 cm) To top of burner grate - Min. 37 3/8 “ (94.9 cm) Additions to Base Height To top of island trim - To top of 6”...
-
Page 3: General Information
2. Legs should be installed near to where the appliance is to be used, as they are not secure for long transit. After unpacking the range, raise it about a foot to remove the bottom shipping skid. Keep the unit raised to permit the legs to be screwed into our couplings and lower it gently to keep any undue strain from the legs and internal mounting hardware. - Page 4 Closely follow the procedures below to ensure proper performance and appearance of the range. 1. If the floor is smooth and level, level the unit with the screw thread of the legs. Set the high corner of the range so that the the top of the side trim is 3/8”...
-
Page 5: Wood/Composite Overlay Installation
WOOD/COMPOSITE OVERLAY INSTALLATION (Including Custom Ventilator Installation) The bottom of a standard hood should be 30” (76.2 cm) min to 36” (91.4 cm) max. above the countertop. This would typically result in the bottom of the hood being 66” (167.6 cm) to 72” (182.9 cm) above the floor. Refer to the rangehood installation instructions for additional information. -
Page 6: Proximity To Side Cabinet Installation
2. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36” (91.4 cm) high. There must be a minimum of 6” (15.2 cm) side clearance from the range to such combustible surfaces above the 36”... -
Page 7: Gas Connection
Gas Connection The gas supply (service) line must be the same size or greater than the inlet line of the appliance. This range uses a 1/2” (1.3 cm) ID NPT (Sch40) inlet. Sealant on all pipe joints must be resistive to LP gas. -
Page 8: Electrical Connection
2. Remove supply cord strain relief bracket and 3-supply cord mounting screws on the terminal block. 3. Feed supply cord up thru the hole in the bottom of the range back. 4. Attach the line #1 (red) and line #2 (black) leads to the outside terminal and the neutral wire (white) to the center terminal on the terminal block. - Page 9 2. Remove strain relief mounting angle and reattach as shown. 3. Feed 1/2” (1.3 cm) trade size conduit through the hole in the bottom of the range back and secure to the strain relief bracket with a conduit clamp. 4. Feed line #1 (red 12 AWG/600v copper conductor), line #2...
- Page 10 Surface Burner Adjustments (Open Top Burners) To gain access to the surface burner adjustments: 1. Remove the grates, bowls, and grate supports. 2. Locate the air shutter “A” and loosen the screw “B” that holds the air shutter in place. 3.
-
Page 11: Grill/Griddle Burner Adjustment
Grill/Griddle Burner Adjustment Grill (Item A) 1. The grill burner orifice and air shutter are located beneath the front end of the grill assembly. To gain access to the adjsutments, remove the grill grate, flavor generator plates, grate support, and the burner shield. 2. -
Page 12: Performance Checklist
Replacement Parts Only authorized replacement parts may be used in performing service on the oven. Replacement parts are available from factory authorized parts distributors. Contact Viking Range Corporation Preferred Service, (888) 845-4641, for the nearest parts distributor in your area.