Advertisement
Quick Links
Hull Length:
Overall length:
Width:
Height:
Weight:
Ba�ery:
Motor:
Charger:
Transmi�er:
Servo:
On-Board Electronics:
INSTRUCTION MANUAL
10" (254mm)
11 5/8" (300mm)
3" (80mm)
2 5/8" (67mm)
6.6 oz. (187g)
7.4V 500mAh Lithium-Ion
180A brushed water-cooled
USB charger
2-channel, 2.4GHz
9g waterproof propor�onal
2-in-1 combo w/ ESC & 2.4GHz receiver
Advertisement
Summary of Contents for Rage RC LightWave
- Page 1 INSTRUCTION MANUAL Hull Length: 10” (254mm) Overall length: 11 5/8” (300mm) Width: 3” (80mm) Height: 2 5/8” (67mm) Weight: 6.6 oz. (187g) Ba�ery: 7.4V 500mAh Lithium-Ion Motor: 180A brushed water-cooled Charger: USB charger Transmi�er: 2-channel, 2.4GHz Servo: 9g waterproof propor�onal On-Board Electronics: 2-in-1 combo w/ ESC &...
- Page 2 A water-cooled 180-size motor combines with a 500mAh Lithium-Ion ba�ery pack to generate fast speeds and long run �mes. And, like most other Rage RC boats, if the LightWave ever flips over when making a �ght turn or running in choppy waters, the self-righ�ng feature quickly turns the boat right side up, so you can con�nue to race.
- Page 3 vehicle, it is strongly recommended that you read the ENTIRE manual before you There is no need to arm the motor, so it will run when you first pull the trigger. Make sure the motor mount is secured to the hull so that the motor does not make sure the boat cannot be controlled by another device.
- Page 4 LightWave before opera�ng. Failure to operate this product correctly can result in damage to the product or personal property, and even cause serious injury. mechanical ability to correctly operate this product. Failure to operate in a safe and responsible manner could result in injury or damage to the product or other prop- erty.
- Page 5 Important Note: Lithium ba�eries are more vola�le than other ba�eries used in RC applica�ons. to the place of purchase immediately. Important • materials. • • • property damage and/or personal injury. DO NOT use a NiCd or NiMh charger to •...
- Page 6 Important Note: (approximately 3.85V per cell) is typically best. This will take some management of the charge 1. Power off your boat. 2. Carefully plug the charger into the USB port on your computer or USB adaptor. 3. Connect the ba�ery to the charger. 4.
-
Page 7: Transmitter Functions
Rotate the hatch lock on the hull cover clockwise to unlock the hatch. Remove the hull cover. Place the ba�ery to the open side of the interior of the hull inside the alignment tabs and plug into the speed control. Ensure that the wires and plug are facing the front of the boat. -
Page 8: Battery Led Monitor
ON/OFF Switch Battery LED Monitor Solid red: Slide the switch Ba�ery is in good condi�on (above 4.3V). up for ON and down for OFF Flashing red with beepings: Ba�ery is at low voltage. Replace ba�eries (below 4.3V). Dual-Rate Functions Adjust the steering control by pressing the switch to the le�... -
Page 9: How To Operate Your Boat
5. If binding is successful, the blinking light will turn solid. If not, start the binding process again with step 1. How to Operate Your Boat With the LightWave, there is no need to Pushing the trigger in the opposite direc�on, or arm the motor. Simply squeeze the trigger in,... - Page 10 Rotate the steering wheel to the le�, or counter- clockwise to turn the boat to the le�. If you find that you need more control, move the Dual Rate switch up for �ghter turns. transmi�er. earlier in this manual...
- Page 11 allow Carefully reinstall the drive sha�, ensuring that there is a 1 to 2 mm gap between the prop sha� and coupling to allow sha� shrinkage under load.
- Page 12 remove close to...
- Page 15 RGRB1132 LightWave Micro RTR Boat; Blue RGRB1133 LightWave Micro RTR Boat; Red RGRB1160 Replacement Printed Hull; Blue RGRB1161 Replacement Printed Hull; Red RGRB1162 Replacement Canopy & Latch; Blue RGRB1167 Replacement Canopy & Latch; Red RGRB1163 Motor Mount RGRB1164 Motor Coupler...
- Page 16 LightWave 08/23...