Related Manuals for SCORPION 10X PRO
Summary of Contents for SCORPION 10X PRO
- Page 1 QUICK-START GUIDE SCORPION 10X PRO Rugged Android Tablet Device BRESSNER Technology GmbH Industriestrasse 51 82194 Groebenzell Phone: +49 (0) 8142 47284-76 E-Mail: scorpion@bressner.de...
- Page 2 OVERVIEW Package content: • 1 x SCORPION 10X PRO • 1 x power adapter (19V/45W) LED indicator Light sensor 2MP IR camera (support Windows hello) Touch Screen Power on/off button Programmable Button (2D Scanner) Programmable Button Volume down 10. Volume up 11.
- Page 3 OVERVIEW 14. Bumper protector 15. Fan cover 16. Ventilation 17. Dummy cover of peripheral kits 18. 8MP rear camera 19. Stylus 20. Batttery box 21. Docking connector 22. Access cover for MicroSD, and expansion GPS antenna 23. Access cover for HDMI, audio jack, USB 3.0 and charging connector 24.
- Page 4 CHARGING 1. Power-on/power-off When the tablet is shipped from the factory, the battery pack is in shipping mode for reducing battery consumption during ship- ment. You must take the battery pack out of shipping mode before the battery pack can be charged and used. To release the battery from shipping mode, please follow the steps: Fully charge the battery when you charge for the first time! Pry open the rubber cover protecting the charging port and plug in the charging cable supplied with the tablet.
- Page 5 CHARGING Press the power button for 1 second to turn on the system. The battery is released from shipping mode after powering on the tablet. If you want to power off the tablet, long press the power button for 4 seconds. Note: For the best touch performance, remove the protective plastic overlay from the LCD screen by peeling it away from one of the corners.
-
Page 6: Replacing The Battery
BATTERY 2. Replacing the battery You can replace the battery either when the tablet is turned off or when the tablet is still running on battery power. Changing a tablet battery without powering off the tablet is called “hot swapping”. To hot swap the battery, please follow the steps: •... -
Page 7: Service Door
SERVICE DOOR 2. Replacing the battery Remove the screws (x4) and rubber pads (x4) of the service door. Gently lift the service door. A swap battery is attached to the service door. Disconnect the connector from the motherboard as the picture shown. Fully release the service door from the system. -
Page 8: Installing Sim Card
SIM CARD 4. Installing SIM Card Remove the screws (x4) and rubber pads (x4) of the service door. Gently lift the service door and be careful not to pull off the cables connecting to the motherboard. To install the SIM card, you need to remove the SSD card first by removing the screw (x1). - Page 9 PERIPHERAL KITS 5. Installing peripheral kits You can expand the capabilities of tablet by connecting the peripheral devices: 2D scanner kit, Long distance 2D scanner kit, COM kit, LAN kit, and USB kit. To install the 2D scanner kit, remove the screws (x2) and rubber pads (x2) to release the dummy cover first. scanner connecter FPC connector Connect the 2D scanner module to the FPC connector on the tablet, then attach the module in place and fasten the screws (x2)
- Page 10 PERIPHERAL KITS Attach the 2D scanner cover and fasten the screws (x2). Last, put on the rubber pads (x2). COM, LAN, and USB kits installation steps are the COM kit same as 2D scanner kit, but the slight difference is you need to place a foam tape pad under the FPC connector on the tablet before connecting the kits.
-
Page 11: Led Indicator
HAND STRAP / LED 6. Attaching hand strap Align and attach the hand strap to the back side of the tablet and fasten the screws (x4) to secure it. 7. LED Indicator Battery level is indicated by the LED indicator on the front of the tablet. GREEN: Battery fully charged (Tablet is plugged in or placed in dock) ORANGE: Battery charging (Tablet is plugged in or placed in dock) -
Page 12: Safety / Disposal
SAFETY / DISPOSAL Safety information Battery Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to the local disposal instructions. Safety ! Regulatory Information Caution: Only use approved and UL listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. - Page 13 2D SCANNER Long distance 2D scanner information Beam divergence: laser aimer pattern (see below figures 1 & 2) Pulse duration: Max. 16.8ms Repetition rate: Max. 16.8ms Maximum power or energy output: Max. laser power 1mW Version 1.00 Technical specifications are subject to change...
Need help?
Do you have a question about the 10X PRO and is the answer not in the manual?
Questions and answers