Advertisement
B. Mounting the E-20B and E-20B-EWP
The E-20B and E-20B-EWP are designed to be surface mounted to a single gang box (not included), a standard 4" x 4" electrical junction box (not
included), or directly to a wall or flat sided post. Caution: For rough surfaces (ie: brick, stucco, etc.) additional caulking may be required.
3.40"
1.55"
3.40"
2.35"
C. Wiring the E-10A and E-10A-EWP
Rear View of the
(Spade
E-10A / E-10A-EWP
connector
included)
** Earth
Ground
(optional)
***** Drip Loop
D. Wiring the E-20B and E-20B-EWP
Rear View of the
E-20B / E-20B-EWP
***** Drip Loop
* Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082
inches. Cut off stripped wire ends before terminating.
** Note: To increase surge protection, loosen the PCB mounting screw labeled
ed) from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)
*** Note: Talk battery must be a minimum of 28V DC when using the speaker phone with a Viking Hot-Line Dialer. For more information on Hot-Line
Dialers, retrieve Fax Back Documents 317.
**** Note: When installing a line powered phone on a low voltage and/or low loop current phone system
extension, a PS-2R Talk Battery/Loop Current boosting power supply may be required.
***** Note: When wires are routed from above, a "drip loop" is recommended to keep water away from the circuit board.
P
r
o
g
r
a
m
m
P
r
o
g
r
a
m
m
A. Adjusting Speaker Volume
The SPKR VOL pot can be adjusted to increase or
decrease the speaker volume to the level desired as shown.
B. Adjusting the Microphone Volume
In certain noisy locations (background traffic, machinery or
wind), the microphone volume may need to be decreased.
A symptom of this is one-way talk path, in which the distant
party cannot be heard over the speaker. A MIC VOL pot is
provided for increasing or decreasing the microphone vol-
ume. Note: If the microphone volume is set too high or too
low, one-way talk path may occur.
Front view of the
E-20B and E-20B-EWP
3.30"
VIKING
©
To open the speaker box, remove
the two screws from the cover.
Viking C-200 Single Entry
Phone Controller (not included)
VIKING
* Gel-Filled Butt
Connectors
Red
(Ring)
or
Green (Tip)
Viking C-200 Single Entry
** Earth Ground
Phone Controller (not included)
(optional)
VIKING
(Spade connector
included)
SINGLE ENTRY PHONE
* Gel-Filled Butt
Connectors
ON
1
2
3
Red
(Ring)
or
Green (Tip)
To dedicated phone, unused trunk/line input of a phone system, or Viking C-1000B Doorbox Controller
i
n
g
i
n
g
Back panel of the
E-20B and E-20B-EWP
UP
Call
Mount back panel to a wall, a single
gang box or a 4"x4" junction box with
the arrow pointing up. Note: For outdoor
applications apply a bead of caulk
between back panel and wall.
Viking C-2000A 1-4 Entry Phone
Controller (not included)
VIKING
MODEL C-200
©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE ENTRY PHONE
CONTROLLER
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5
6 7 8 9 10
ON
1
2
3
EARTH
C.O. LINE
OUT TO
ENTRY
N.O. COM N.C.
GND
INPUT
PHONES
PHONE
AUX CONTACTS
Viking C-2000A 1-4 Entry Phone
Controller (not included)
VIKING
©
MODEL C-200
©
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
CONTROLLER
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5
6 7 8 9 10
11 12 13 14 15
EARTH
C.O. LINE
OUT TO
ENTRY
N.O. COM N.C.
GND
INPUT
PHONES
PHONE
AUX CONTACTS
(as shown above) and fasten a wire with spade terminal (includ-
Rear View of the Speaker Phone models:
E-10A / E-10A-EWP / E-20B / E-20B-EWP
Side view of the
E-20B and E-20B-EWP
Attach the cover to the base
with the two included screws
as shown.
*** Optional Viking
K-1900-5 Dialer
MODEL C-2000A
©
(not included)
VIKING
ELECTRONICS
HUDSON, WI 54016
VIKING
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
©
Programmable
Tone Dialer
MODEL: K-1900-5
Quick Programming Guide
1. Call the phone connected to the dialer.
∗
2. Answer phone. Enter
& security code.
(Factory set to 845464) Write your
security code below:
3. Enter your spped dial number & #00.
Note: For additional programming see
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
K-1900-5 Technical Practice.
Viking Electronics, Inc.
Hudson, WI 54016
LINE IN
PHONE
To C.O. Line or
PABX/KSU station
To dedicated phone, unused trunk/line input of a phone
system, or Viking C-1000B Doorbox Controller
*** Optional Viking
K-1900-5 Dialer
MODEL C-2000A
(not included)
VIKING
ELECTRONICS
HUDSON, WI 54016
VIKING
©
Programmable
Tone Dialer
MODEL: K-1900-5
Quick Programming Guide
1. Call the phone connected to the dialer.
∗
2. Answer phone. Enter
& security code.
(Factory set to 845464) Write your
security code below:
3. Enter your spped dial number & #00.
Note: For additional programming see
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
K-1900-5 Technical Practice.
Viking Electronics, Inc.
Hudson, WI 54016
LINE IN
PHONE
To C.O. Line or
PABX/KSU station
Need More Information on the PS-2R?
?
Call (715) 386-4345 and select 512.
ON
1 2 3
1 2 3
**** C.O. Line or Analog
PABX/KSU Station
(programmed for ringdown)
Viking DLE-200B
Two Way Ringdown
Circuit (not included)
VIKING
RINGDOWN
©
1
2
DLE-200B
RES
BUSY
**** C.O. Line or Analog
PABX/KSU Station
(programmed for ringdown)
Viking DLE-200B
Two Way Ringdown
Circuit (not included)
VIKING
RINGDOWN
©
1
2
DLE-200B
RES
BUSY
Less (-)
Speaker Volume
(shown in default positions)
More (+)
Less (-)
Microphone Volume
(shown in default positions)
More (+)
ON
S1
DIP Switches
(shown in default positions)
OFF
Advertisement
