Advertisement
COMPATIBLE BATTERY PACKS (NOT INCLUDED)
L1820R
A18B4
L1820S
L1840R
A18FB2
A18FB4
L1825R
L1850R
L1830R-X5
A18FB5
Use AEG 18V battery and charger only
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
RIGHT ANGLE IMPACT WRENCH SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory or
fasteners may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Ambient temperature range for tool during operation is between
0°C and 40°C.
Ambient temperature range for tool storage is between 0°C and
40°C.
The recommended ambient temperature range for the charging
system during charging is between 10°C and 38°C.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the product. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy non-
slip footwear, helmet and ear defenders.
The dust produced when using this product may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Do not direct the light beam at persons or animals and do not stare
into the light beam yourself (not even from a distance). Staring into
the light beam may result in serious injury or vision loss.
The product is not waterproof. Do not submerge in liquid. Failure to
heed this warning could result in serious personal injury.
Switch the product off immediately if the accessory stalls! Do
not switch the device on again while the accessory is stalled, as
doing so could trigger a sudden recoil with a high reactive force.
Determine why the accessory stalled and rectify this, paying heed
to the safety instructions.
The possible causes may be:
■
it is tilted in the workpiece to be machined
■
it has pierced through the material to be machined
■
the power product is overloaded
Do not reach into the product while it is running. The accessory
may become hot during use.
WARNING! Danger of burns
■
when changing products
■
when setting the device down
Chips and splinters must not be removed while the product is
running.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove battery pack before storing or transporting the product.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING! To reduce the risk of fire, personal injury, and
product damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
L1860R
Remove the battery pack before starting any work on the product.
L1860R-X5
Do not dispose of used battery packs in the household refuse or
L1890R
by burning them. AEG Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System AEG chargers for charging System AEG battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Check with the forwarding company for further advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise and the operator should pay special attention to
avoid the following:
■
Injury caused by vibration
●
■
Exposure to noise can cause hearing injury
●
■
Injury due to flying debris
●
■
Inhalation of toxic dusts
●
●
●
RISK REDUCTION
It has been reported that vibrations from handheld products may
contribute to a condition called Raynaud's Syndrome in certain
individuals. Symptoms may include tingling, numbness and
blanching of the fingers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet, smoking
and work practices are all thought to contribute to the development
of these symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■
Keep your body warm in cold weather. When operating the unit
wear gloves to keep the hands and wrists warm. It is reported
that cold weather is a major factor contributing to Raynaud's
Syndrome.
■
After each period of operation, exercise to increase blood
circulation.
■
Take frequent work breaks. Limit the amount of exposure per
day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about these
symptoms.
WARNING! Injuries may be caused or aggravated by
prolonged use of a product. When using any product for prolonged
periods, ensure you take regular breaks.
SPECIFIED CONDITIONS OF USE
The right angle impact wrench is intended for fastening and
loosening bolts and nuts.
Do not use the product for any other purpose.
Hold the product by designated handles and restrict
working time and exposure.
Wear ear protection and limit exposure.
Wear eye protection, heavy long trousers, gloves and
substantial footwear at all times.
Wear respiratory protection masks containing filters
appropriate to the materials being worked.
Ensure adequate workplace ventilation.
Do not eat, drink or smoke in the work area.
9
Advertisement
