1. Complete Unit Circuit diagram POWER SWITCH LCD PANEL CON 1 POWER BOARD SPEAKER CN11 CN22 REMOTE BOARD CON 2 AUDIO VIDEO MAIN BOARD DVD_IR KEY BOARD ON/ OFF ADJ DVD CD RO / DECODE BOARD DVD KEY BOARD...
1) Power problem If F1/3A with 12V? Check fuse FI or external power E33/470μF/16V if Voltage is5 V Fuse burnt when power on? Check if can power on Check power output (via button or R/C) (U16,U18,U19) Check F1 descending Check U21: if Check if the second Power supply network power supply,...
Page 5
2) Display problem(display Mosaic distortion/Mosaic) Check if the cable connected to panel is right and works normally Check if panel is ok? Check if the output of U5 cable socket is ok? Change the cable which drives the panel Change Check the power supply panel And timer circuit of U5...
Page 6
3)、Display problem (white screen) White screen Check if Voltage for panel is ok?( depend on the selected panel) Check G pole of Q24/AO3401 has Check if U5 has signal output? the change of 3.3-0V or 5-0V Check the circuit from the 98 U5 defective or Panel defective or CN8 connecting defective...
Page 7
4)、Display problem (black screen) Black screen Is there 5V backlight voltage (BLON) at CN19? Check if inverter power supply works nomally? Check the circuit of Q26 or I/O port of U21 (99 pin) Check the Replace Inverter external power supply...
Page 8
5).Audio problem No sound (No sound) Check if there is Audio input Is volume, MUTE settings correct? Is there signal output at CN11? Check if voltage at the 7 pin of U3/TPA1517NE is higher than 11V pin of U3 is higher or Check if voltage at the 8 equal to 9.2V Check if the 1...
Page 9
6) Functionare (TV TV no channel scan/no video Video) Check if RF imput signal is ok? Check voltage at the 7 of T1/TEDE9-2B4A is 5V? Check voltage at the 9 pin of T1 is 33V? Check voltage at the 3 pin of T1 is 0V? Check: is there I2C data at the 4 &5...
Page 10
7).Functionare(TV TV no sound,but have Audio) video Check if audio is ok under PC/AV modes Check is there signal at the 2 pin of SAW2/AF389A2D Check if the 1. SAW2 damaged circuit between 2. U21: the 29 Refer to “No sound” the 2 pin of pin have solder...
Page 11
8).Functionare(PC) PC Mode Video Video No signal centered Discolored viabration Check if R.G.B input signal Check if VS.HS signal is stable and regular? works well seetings System Run auto-adjust Check R.G.B Check VS.HS mismatch Check VS.HS settings is command circuit circuit input circuit...
Page 12
9)、Functionare(SCART、AV、S-V) SCART RGB、SCART Video、S- Video、AV下 No signal at all channels No signal Discolored except VGA Check if R.G.B input signal of U5 is ok? Check R.G.B System circuit (Under Check power Check VS.HS settings is SCART R.G.B mode, supply of U21 circuit incorrect.
Page 13
3. DVD Decode Board Operational Troubleshooting Display Troubleshooting Audio Troubleshooting Disc Playing Troubleshooting...
Page 14
Power on 1. Initialize related registers (servo,DSP,RISC) 2. Move code related with RISC to SDRAM 3. Reset RISC Display LOGO Does tray close? Close tray Does SLED move to inside? Move to inside 1. Judge if a disc has loaded 2.
Page 15
Power on Voltages 1. Check cable in all pins of item PWR CON 2. Check power block circuit aer normal Check LDO B1117-3V3 and Are 3V3 and 1V8 normal? B1117-1V8 and peripheral circuit Is Main Clock normal? Check oscillation circuit Display LOGO? Check reset circuit reset singal normal?
Page 16
If will the tray close Check the position-switch Signal TRAYOUT and automatically when it is open? in LOADER TRAYIN is correct? Check the circuit between SPHE8281D and driver circuit Signal TRAY+ & TRAY- correct? SS8050 SS8550 TO-92 footprint Check motor driver circuit Signal LOAD+ &...
Page 17
Check the peripheral circuit of Signal CDLDO and SPHE8281D & two transistor When read disc, Laser ON OK? DVDLDO is normal? (2SB1132) Check the peripheral circuit of Voltage of TP18 & TP21 OK? of two transistor (2SB1132) Check the circuit to connect loader OPU maybe damaged Load a disc? Laser off...
Page 18
Check SPHE8281D and its Signal TEO peripheral circuit Track on OK? (pin35 of SPHE8281D) normal? Signal TCO Check the TCO connection between SPHE8281D(pin42 and pin36) (pin42 of SPHE8281D) normal? Check SPHE8281D and its peripheral Signal RAD+ & RAD- normal? circuit Check the connection between OPU and BA5954FP Disc is ready?